AT32UC3A3128 Atmel Corporation, AT32UC3A3128 Datasheet - Page 746

• Manufacturer Part Number: AT32UC3A3128
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A3128

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 110
• Ext Interrupts: 110
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 12
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

27.6.1.5
32072G–11/2011
TC operating modes
Figure 27-3. Clock Control
Each channel can independently operate in two different modes:
The TC operating mode selection is done by writing to the Wave bit in the CCRn register
(CCRn.WAVE).
In Capture mode, TIOA and TIOB are configured as inputs.
In Waveform mode, TIOA is always configured to be an output and TIOB is an output if it is not
selected to be the external trigger.
• The clock can be enabled or disabled by the user by writing to the Counter Clock
• The clock can also be started or stopped: a trigger (software, synchro, external or compare)
• Capture mode provides measurement on signals.
• Waveform mode provides wave generation.
Enable/Disable Command bits in the Channel n Clock Control Register (CCRn.CLKEN and
CCRn.CLKDIS). In Capture mode it can be disabled by an RB load event if the Counter
Clock Disable with RB Loading bit in CMRn is written to one (CMRn.LDBDIS). In Waveform
mode, it can be disabled by an RC Compare event if the Counter Clock Disable with RC
Compare bit in CMRn is written to one (CMRn.CPCDIS). When disabled, the start or the stop
actions have no effect: only a CLKEN command in CCRn can re-enable the clock. When the
clock is enabled, the Clock Enabling Status bit is set in SRn (SRn.CLKSTA).
always starts the clock. In Capture mode the clock can be stopped by an RB load event if the
Counter Clock Stopped with RB Loading bit in CMRn is written to one (CMRn.LDBSTOP). In
Waveform mode it can be stopped by an RC compare event if the Counter Clock Stopped
with RC Compare bit in CMRn is written to one (CMRn.CPCSTOP). The start and the stop
commands have effect only if the clock is enabled.
Selected
Clock
Counter
Clock
Q
S
R
Trigger
CLKSTA
Q
CLKEN
S
R
Event
Stop
CLKDIS
Disable
Event
746