AT90USB1286 Atmel Corporation, AT90USB1286 Datasheet - Page 160

• Manufacturer Part Number: AT90USB1286
• Manufacturer: Atmel Corporation

Specifications of AT90USB1286

• Flash (kbytes): 128 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 48
• Ext Interrupts: 16
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 8
• Eeprom (bytes): 4096
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 10
• Input Capture Channels: 1
• Pwm Channels: 9
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

15.8
15.8.1
160
8-bit Timer/Counter Register Description
AT90USB64/128
Timer/Counter Control Register A – TCCR2A
Figure 15-11. Timer/Counter Timing Diagram, Clear Timer on Compare Match mode, with Pres-
• Bits 7:6 – COM2A1:0: Compare Match Output A Mode
These bits control the Output Compare pin (OC2A) behavior. If one or both of the COM2A1:0
bits are set, the OC2A output overrides the normal port functionality of the I/O pin it is connected
to. However, note that the Data Direction Register (DDR) bit corresponding to the OC2A pin
must be set in order to enable the output driver.
When OC2A is connected to the pin, the function of the COM2A1:0 bits depends on the
WGM22:0 bit setting.
are set to a normal or CTC mode (non-PWM).
Table 15-1.
Bit
Read/Write
Initial Value
COM2A1
0
0
1
1
TCNTn
(clk
OCRnx
(CTC)
OCFnx
clk
clk
I/O
I/O
Tn
/8)
7
COM2A
1
R/W
0
caler (f
Compare Output Mode, non-PWM Mode
COM2A0
0
1
0
1
clk_I/O
Table 15-1
6
COM2A
0
R/W
0
TOP - 1
/8)
Description
Normal port operation, OC2A disconnected.
Toggle OC2A on Compare Match
Clear OC2A on Compare Match
Set OC2A on Compare Match
5
COM2B
1
R/W
0
shows the COM2A1:0 bit functionality when the WGM22:0 bits
4
COM2B
0
R/W
0
TOP
3
–
R
0
TOP
2
–
R
0
BOTTOM
1
WGM2
1
R/W
0
0
WGM2
0
R/W
0
BOTTOM + 1
TCCR2A
7593K–AVR–11/09