AT90USB1286 Atmel Corporation, AT90USB1286 Datasheet - Page 64

• Manufacturer Part Number: AT90USB1286
• Manufacturer: Atmel Corporation

Specifications of AT90USB1286

• Flash (kbytes): 128 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 48
• Ext Interrupts: 16
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 8
• Eeprom (bytes): 4096
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 10
• Input Capture Channels: 1
• Pwm Channels: 9
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

64
AT90USB64/128
The following code example shows one assembly and one C function for turning off the Watch-
dog Timer. The example assumes that interrupts are controlled (e.g. by disabling interrupts
globally) so that no interrupts will occur during the execution of these functions.
Note:
Assembly Code Example
C Code Example
1. In the same operation, write a logic one to the Watchdog change enable bit (WDCE)
2. Within the next four clock cycles, write the WDE and Watchdog prescaler bits (WDP) as
WDT_off:
void WDT_off(void)
{
*/
}
and WDE. A logic one must be written to WDE regardless of the previous value of the
WDE bit.
desired, but with the WDCE bit cleared. This must be done in one operation.
; Turn off global interrupt
cli
; Reset Watchdog Timer
wdr
; Clear WDRF in MCUSR
in
andi
out
; Write logical one to WDCE and WDE
; Keep old prescaler setting to prevent unintentional time-out
in
ori
out
; Turn off WDT
ldi
out
; Turn on global interrupt
sei
ret
__disable_interrupt();
__watchdog_reset();
/* Clear WDRF in MCUSR */
MCUSR &= ~(1<<WDRF);
/* Write logical one to WDCE and WDE */
/* Keep old prescaler setting to prevent unintentional time-out
WDTCSR |= (1<<WDCE) | (1<<WDE);
/* Turn off WDT */
WDTCSR = 0x00;
__enable_interrupt();
1. The example code assumes that the part specific header file is included.
r16, MCUSR
r16, ~(0<<WDRF)
MCUSR, r16
r16, WDTCSR
r16, (1<<WDCE) | (1<<WDE)
WDTCSR, r16
r16, (0<<WDE)
WDTCSR, r16
(1)
(1)
7593K–AVR–11/09