AT90USB1286 Atmel Corporation, AT90USB1286 Datasheet - Page 255

• Manufacturer Part Number: AT90USB1286
• Manufacturer: Atmel Corporation

Specifications of AT90USB1286

• Flash (kbytes): 128 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 48
• Ext Interrupts: 16
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 8
• Eeprom (bytes): 4096
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 10
• Input Capture Channels: 1
• Pwm Channels: 9
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

21.5
21.5.1
21.5.2
7593K–AVR–11/09
Power modes
Idle mode
Power down
Figure 21-13. USB General and OTG Controller Interrupt System
There are 2 kind of interrupts: processing (i.e. their generation are part of the normal processing)
and exception (errors).
Processing interrupts are generated when such events occur :
Exception Interrupts are generated with the following events :
In this mode, the CPU core is halted (CPU clock stopped). The Idle mode is taken wether the
USB controller is running or not. The CPU “wakes up” on any USB interrupts.
In this mode, the oscillator is stopped and halts all the clocks (CPU and peripherals). The USB
controller “wakes up” when:
• USB ID Pad change detection (insert, remove)(IDTI)
• VBUS plug-in detection (insert, remove) (VBUSTI)
• SRP detected(SRPI)
• Role Exchanged(ROLEEXI)
• Drop on VBus Detected(VBERRI)
• Error during the B-Connection(BCERRI)
• HNP Error(HNPERRI)
• Time-out detected during Suspend mode(STOII)
• the WAKEUPI interrupt is triggered in the Peripheral mode (HOST cleared),
OTGINT.5
OTGINT.4
OTGINT.3
OTGINT.2
OTGINT.1
OTGINT.0
USBINT.1
USBINT.0
ROLEEXI
HNPERRI
BCERRI
VBUSTI
VBERRI
STOI
SRPI
IDTI
USBCON.1
USBCON.0
OTGIEN.5
OTGIEN.4
ROLEEXE
OTGIEN.3
OTGIEN.2
OTGIEN.1
OTGIEN.0
HNPERRE
BCERRE
VBERRE
VBUSTE
STOE
SRPE
IDTE
USB General & OTG
Asynchronous Interrupt source
(allows the CPU to wake up from power down mode)
Interrupt Vector
AT90USB64/128
255