AT90USB1286 Atmel Corporation, AT90USB1286 Datasheet - Page 377

• Manufacturer Part Number: AT90USB1286
• Manufacturer: Atmel Corporation

Specifications of AT90USB1286

• Flash (kbytes): 128 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 48
• Ext Interrupts: 16
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 8
• Eeprom (bytes): 4096
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 10
• Input Capture Channels: 1
• Pwm Channels: 9
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

29.6.9
29.6.10
29.6.11
7593K–AVR–11/09
Programming the Fuse High Bits
Programming the Extended Fuse Bits
Programming the Lock Bits
The algorithm for programming the Fuse High bits is as follows (refer to
Flash” on page 373
The algorithm for programming the Extended Fuse bits is as follows (refer to
Flash” on page 373
Figure 29-5. Programming the FUSES Waveforms
The algorithm for programming the Lock bits is as follows (refer to
page 373
The Lock bits can only be cleared by executing Chip Erase.
1. A: Load Command “0100 0000”.
2. C: Load Data Low Byte. Bit n = “0” programs and bit n = “1” erases the Fuse bit.
3. Set BS2, BS1 to “01”. This selects high data byte.
4. Give WR a negative pulse and wait for RDY/BSY to go high.
5. Set BS2, BS1 to “00”. This selects low data byte.
1. 1. A: Load Command “0100 0000”.
2. 2. C: Load Data Low Byte. Bit n = “0” programs and bit n = “1” erases the Fuse bit.
3. 3. Set BS2, BS1 to “10”. This selects extended data byte.
4. 4. Give WR a negative pulse and wait for RDY/BSY to go high.
5. 5. Set BS2, BS1 to “00”. This selects low data byte.
1. A: Load Command “0010 0000”.
2. C: Load Data Low Byte. Bit n = “0” programs the Lock bit. If LB mode 3 is programmed
3. Give WR a negative pulse and wait for RDY/BSY to go high.
RESET +12V
(LB1 and LB2 is programmed), it is not possible to program the Boot Lock bits by any
External Programming mode.
RDY/BSY
PAGEL
XTAL1
DATA
for details on Command and Data loading):
XA1
XA0
BS1
BS2
WR
OE
0x40
A
for details on Command and Data loading):
for details on Command and Data loading):
DATA
C
Write Fuse Low byte
XX
0x40
A
DATA
C
Write Fuse high byte
XX
AT90USB64/128
“Programming the Flash” on
0x40
A
DATA
C
Write Extended Fuse byte
“Programming the
“Programming the
XX
377