AT90USB1286 Atmel Corporation, AT90USB1286 Datasheet - Page 82

• Manufacturer Part Number: AT90USB1286
• Manufacturer: Atmel Corporation

Specifications of AT90USB1286

• Flash (kbytes): 128 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 48
• Ext Interrupts: 16
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 8
• Eeprom (bytes): 4096
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 10
• Input Capture Channels: 1
• Pwm Channels: 9
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

82
AT90USB64/128
PCINT1, Pin Change Interrupt source 1: The PB1 pin can serve as an external interrupt source.
• SS/PCINT0 – Port B, Bit 0
SS: Slave Port Select input. When the SPI is enabled as a slave, this pin is configured as an
input regardless of the setting of DDB0. As a slave, the SPI is activated when this pin is driven
low. When the SPI is enabled as a master, the data direction of this pin is controlled by DDB0.
When the pin is forced to be an input, the pull-up can still be controlled by the PORTB0 bit.
Table 10-7
shown in
MISO signal, while MOSI is divided into SPI MSTR OUTPUT and SPI SLAVE INPUT.
PCINT0, Pin Change Interrupt source 0: The PB0 pin can serve as an external interrupt source..
Table 10-7.
Table 10-8.
Signal
Name
PUOE
PUOV
DDOE
DDOV
PVOE
PVOV
DIEOE
DIEOV
DI
AIO
Signal
Name
PUOE
PUOV
DDOE
DDOV
PVOE
PVOV
DIEOE
DIEOV
DI
AIO
Figure 10-5 on page
PB7/PCINT7/OC0A/
OC1C
0
0
0
0
OC0/OC1C ENABLE
OC0/OC1C
PCINT7 • PCIE0
1
PCINT7 INPUT
–
PB3/PD0/PCINT3/
MISO
SPE • MSTR
PORTB3 • PUD
SPE • MSTR
0
SPE • MSTR
SPI SLAVE OUTPUT
PCINT3 • PCIE0
1
SPI MSTR INPUT
PCINT3 INPUT
–
and
Overriding Signals for Alternate Functions in PB7..PB4
Overriding Signals for Alternate Functions in PB3..PB0
Table 10-8
relate the alternate functions of Port B to the overriding signals
77. SPI MSTR INPUT and SPI SLAVE OUTPUT constitute the
PB2/PDI/PCINT2/
MOSI
SPE • MSTR
PORTB2 • PUD
SPE • MSTR
0
SPE • MSTR
SPI MSTR OUTPUT
PCINT2 • PCIE0
1
SPI SLAVE INPUT
PCINT2 INPUT
–
PB6/PCINT6/OC
1B
0
0
0
0
OC1B ENABLE
OC1B
PCINT6 • PCIE0
1
PCINT6 INPUT
–
PB5/PCINT5/OC
1A
0
0
0
0
OC1A ENABLE
OC1A
PCINT5 • PCIE0
1
PCINT5 INPUT
–
PB1/PCINT1/
SCK
SPE • MSTR
PORTB1 • PUD
SPE • MSTR
0
SPE • MSTR
SCK OUTPUT
PCINT1 •
PCIE0
1
SCK INPUT
PCINT1 INPUT
–
PB4/PCINT4/OC
2A
0
0
0
0
OC2A ENABLE
OC2A
PCINT4 • PCIE0
1
PCINT4 INPUT
–
PB0/PCINT0/
SS
SPE • MSTR
PORTB0 • PUD
SPE • MSTR
0
0
0
PCINT0 •
PCIE0
1
SPI SS
PCINT0 INPUT
–
7593K–AVR–11/09