AT90USB1286 Atmel Corporation, AT90USB1286 Datasheet - Page 326

• Manufacturer Part Number: AT90USB1286
• Manufacturer: Atmel Corporation

Specifications of AT90USB1286

• Flash (kbytes): 128 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 48
• Ext Interrupts: 16
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 8
• Eeprom (bytes): 4096
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 10
• Input Capture Channels: 1
• Pwm Channels: 9
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

25.8
25.8.1
326
ADC Register Description
AT90USB64/128
ADC Multiplexer Selection Register – ADMUX
Table 25-2.
Example 1:
Example 2:
• Bit 7:6 – REFS1:0: Reference Selection Bits
These bits select the voltage reference for the ADC, as shown in
changed during a conversion, the change will not go in effect until this conversion is complete
Bit
Read/Write
Initial Value
V
V
V
...
V
V
V
...
V
V
V
ADCn
ADCm
ADCm
ADCm
ADCm
ADCm
ADCm
ADCm
ADCm
– ADMUX = 0xED (ADC3 - ADC2, 10x gain, 2.56V reference, left adjusted result)
– Voltage on ADC3 is 300 mV, voltage on ADC2 is 500 mV.
– ADCR = 512 * 10 * (300 - 500) / 2560 = -400 = 0x270
– ADCL will thus read 0x00, and ADCH will read 0x9C.
– ADMUX = 0xFB (ADC3 - ADC2, 1x gain, 2.56V reference, left adjusted result)
– Voltage on ADC3 is 300 mV, voltage on ADC2 is 500 mV.
– ADCR = 512 * 1 * (300 - 500) / 2560 = -41 = 0x029.
– ADCL will thus read 0x40, and ADCH will read 0x0A.
+ 0.999 V
+ 0.998 V
+ 0.001 V
- 0.001 V
- 0.999 V
- V
Writing zero to ADLAR right adjusts the result: ADCL = 0x70, ADCH = 0x02.
Writing zero to ADLAR right adjusts the result: ADCL = 0x00, ADCH = 0x29.
+ V
REF
REF
/GAIN
REFS1
/GAIN
Correlation Between Input Voltage and Output Codes
R/W
REF
REF
7
0
REF
REF
REF
/GAIN
/GAIN
/GAIN
/GAIN
/GAIN
REFS0
R/W
6
0
ADLAR
Read code
R/W
5
0
0x1FF
0x1FF
0x1FE
0x3FF
0x001
0x000
0x201
0x200
...
...
MUX4
R/W
4
0
Corresponding decimal value
511
511
510
...
1
0
-1
...
-511
-512
MUX3
R/W
3
0
MUX2
R/W
2
0
MUX1
R/W
1
0
Table
MUX0
R/W
0
0
25-3. If these bits are
ADMUX
7593K–AVR–11/09