ATtiny43U Atmel Corporation, ATtiny43U Datasheet - Page 136

• Manufacturer Part Number: ATtiny43U
• Manufacturer: Atmel Corporation

Specifications of ATtiny43U

• Flash (kbytes): 4 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 8 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 16
• Ext Interrupts: 16
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 4
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.25
• Eeprom (bytes): 64
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 0.7 to 5.5
• Operating Voltage (vcc): 0.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 4
• Pwm Channels: 4
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

18.6.3
136
ATtiny43U
Reading Device Signature Imprint Table from Firmware
To read the Fuse High Byte (FHB), simply replace the address in the Z-pointer with 0x0003 and
repeat the procedure above. If successful, the contents of the destination register are as follows.
Refer to
To read the Fuse Extended Byte (FEB), replace the address in the Z-pointer with 0x0002 and
repeat the previous procedure. If successful, the contents of the destination register are as
follows.
Refer to
Byte.
To read the contents of the device signature imprint table, follow the below procedure:
See program example below.
Note:
If successful, the contents of the destination register are as described in section
ture Imprint Table” on page
Bit
Rd
Bit
Rd
Assembly Code Example
1. Load the Z-pointer with the table index.
2. Set RSIG and SPMEN bits in SPMCSR.
3. Issue an LPM instruction within three clock cycles.
4. Read table data from the LPM destination register.
DSIT_read:
; Uses Z-pointer as table index
ldi
ldi
; Preload SPMCSR bits into R16, then write to SPMCSR
ldi
out SPMCSR, r16
; Issue LPM. Table data will be returned into r17
lpm r17, Z
ret
See
Table 19-4 on page 140
Table 19-3 on page 140
“Code Examples” on page
ZH, 0
ZL, 1
r16, (1<<RSIG)|(1<<SPMEN)
FHB7
FEB7
7
7
FHB6
FEB6
6
6
141.
for detailed description and mapping of the Fuse High Byte.
FHB5
FEB5
for detailed description and mapping of the Fuse Extended
5
5
6.
FHB4
FEB4
4
4
FHB3
FEB3
3
3
FHB2
FEB2
2
2
FHB1
FEB1
1
1
FHB0
FEB0
“Device Signa-
0
0
8048B–AVR–03/09