PIC18F24J10-E/ML MICROCHIP [Microchip Technology], PIC18F24J10-E/ML Datasheet - Page 209

• Manufacturer Part Number: PIC18F24J10-E/ML
• Description: 28/40/44-Pin High-Performance RISC Microcontrollers with nanoWatt Technology
• Manufacturer: MICROCHIP [Microchip Technology]

16.4.2
The operation of the Synchronous Master and Slave
modes is identical, except in the case of Sleep, or any
Idle mode and bit SREN, which is a “don’t care” in
Slave mode.
If receive is enabled by setting the CREN bit prior to
entering Sleep or any Idle mode, then a word may be
received while in this low-power mode. Once the word
is received, the RSR register will transfer the data to the
RCREG register; if the RCIE enable bit is set, the inter-
rupt generated will wake the chip from the low-power
mode. If the global interrupt is enabled, the program will
branch to the interrupt vector.
TABLE 16-10: REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE RECEPTION
© 2007 Microchip Technology Inc.
INTCON
PIR1
PIE1
IPR1
RCSTA
RCREG
TXSTA
BAUDCON
SPBRGH
SPBRG
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous slave reception.
Note 1:
Name
These bits are not implemented on 28-pin devices and should be read as ‘0’.
EUSART SYNCHRONOUS SLAVE
RECEPTION
EUSART Receive Register
EUSART Baud Rate Generator Register High Byte
EUSART Baud Rate Generator Register Low Byte
GIE/GIEH PEIE/GIEL TMR0IE
ABDOVF
PSPIE
PSPIP
PSPIF
CSRC
SPEN
Bit 7
(1)
(1)
(1)
RCIDL
ADIE
ADIP
Bit 6
ADIF
RX9
TX9
SREN
TXEN
RCIE
RCIP
RCIF
Bit 5
—
Preliminary
INT0IE
CREN
SYNC
SCKP
Bit 4
TXIF
TXIE
TXIP
PIC18F45J10 FAMILY
SSP1IF
SSP1IE
SSP1IP
ADDEN
SENDB
BRG16
To set up a Synchronous Slave Reception:
1.
2.
3.
4.
5.
6.
7.
8.
9.
RBIE
Bit 3
Enable the synchronous master serial port by
setting bits SYNC and SPEN and clearing bit
CSRC.
If interrupts are desired, set enable bit RCIE.
If 9-bit reception is desired, set bit RX9.
To enable reception, set enable bit CREN.
Flag bit, RCIF, will be set when reception is
complete. An interrupt will be generated if
enable bit, RCIE, was set.
Read the RCSTA register to get the 9th bit (if
enabled) and determine if any error occurred
during reception.
Read the 8-bit received data by reading the
RCREG register.
If any error occurred, clear the error by clearing
bit CREN.
If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
TMR0IF
CCP1IF
CCP1IE
CCP1IP
BRGH
FERR
Bit 2
—
TMR2IF
TMR2IE
TMR2IP
INT0IF
OERR
TRMT
WUE
Bit 1
TMR1IE
TMR1IP
TMR1IF
ABDEN
RX9D
TX9D
DS39682C-page 207
RBIF
Bit 0
on page
Values
Reset
43
45
45
45
45
45
45
45
45
45