PIC18F25K80 MICROCHIP [Microchip Technology], PIC18F25K80 Datasheet - Page 298

no-image

PIC18F25K80

Manufacturer Part Number
PIC18F25K80
Description
Manufacturer
MICROCHIP [Microchip Technology]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PIC18F25K80-E/MM
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
PIC18F25K80-E/SO
Quantity:
149
Part Number:
PIC18F25K80-E/SS
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
PIC18F25K80-H/MM
Manufacturer:
MITSUBISHI
Quantity:
56
Company:
Part Number:
PIC18F25K80-H/MM
Quantity:
12 600
Part Number:
PIC18F25K80-I/MM
Manufacturer:
MICROCHIP
Quantity:
2 400
Part Number:
PIC18F25K80-I/MM
0
Part Number:
PIC18F25K80-I/SO
Manufacturer:
MICROCHIP
Quantity:
3 000
Part Number:
PIC18F25K80-I/SP
Manufacturer:
MICROCHIP
Quantity:
147
Part Number:
PIC18F25K80-I/SP
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
PIC18F25K80-I/SS
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
PIC18F25K80-I/SS
0
Company:
Part Number:
PIC18F25K80-I/SS
Quantity:
5
Company:
Part Number:
PIC18F25K80T-H/MM
Quantity:
12 600
Part Number:
PIC18F25K80T-I/MM
Manufacturer:
MICROCHIP
Quantity:
3 000
Part Number:
PIC18F25K80T-I/SS
Manufacturer:
MICROCHIT
Quantity:
20 000
Part Number:
PIC18F25K80T-I/SS
0
Company:
Part Number:
PIC18F25K80T-I/SS
Quantity:
4 200
PIC18F66K80 FAMILY
21.3.6
The master can initiate the data transfer at any time
because it controls the SCK. The master determines
when the slave (Processor 1,
broadcast data by the software protocol.
In Master mode, the data is transmitted/received as
soon as the SSPBUF register is written to. If the SPI is
only going to receive, the SDO output could be dis-
abled (programmed as an input). The SSPSR register
will continue to shift in the signal present on the SDI pin
at the programmed clock rate. As each byte is
received, it will be loaded into the SSPBUF register as
if a normal received byte (interrupts and status bits
appropriately set). This could be useful in receiver
applications as a “Line Activity Monitor” mode.
The clock polarity is selected by appropriately
programming the CKP bit (SSPCON1<4>). This then,
would give waveforms for SPI communication as
FIGURE 21-3:
DS39977C-page 298
Write to
SSPBUF
SCK
(CKP = 0
CKE = 0)
SCK
(CKP = 1
CKE = 0)
SCK
(CKP = 0
CKE = 1)
SCK
(CKP = 1
CKE = 1)
SDO
(CKE = 0)
SDO
(CKE = 1)
SDI
(SMP = 0)
Input
Sample
(SMP = 0)
SDI
(SMP = 1)
Input
Sample
(SMP = 1)
SSPIF
SSPSR to
SSPBUF
MASTER MODE
SPI MODE WAVEFORM (MASTER MODE)
bit 7
bit 7
bit 7
bit 7
Figure
bit 6
bit 6
21-2) is to
bit 5
bit 5
Preliminary
bit 4
bit 4
bit 3
bit 3
shown in
where the MSB is transmitted first. In Master mode, the
SPI clock rate (bit rate) is user-programmable to be one
of the following:
• F
• F
• F
• Timer2 output/2
This allows a maximum data rate (at 64 MHz) of
16 Mbps.
Figure 21-3
When the CKE bit is set, the SDO data is valid before
there is a clock edge on SCK. The change of the input
sample is shown based on the state of the SMP bit. The
time when the SSPBUF is loaded with the received
data is shown.
OSC
OSC
OSC
/4 (or T
/16 (or 4 • T
/64 (or 16 • T
bit 2
bit 2
Figure
shows the waveforms for Master mode.
CY
)
bit 1
bit 1
21-3,
CY
CY
)
)
 2011 Microchip Technology Inc.
Figure 21-5
bit 0
bit 0
bit 0
bit 0
Next Q4 Cycle
after Q2
and
Four Clock
Modes
Figure
21-6,

Related parts for PIC18F25K80