PIC18F25K80 MICROCHIP [Microchip Technology], PIC18F25K80 Datasheet - Page 410

• Manufacturer Part Number: PIC18F25K80
• Manufacturer: MICROCHIP [Microchip Technology]

PIC18F66K80 FAMILY
27.2.3
This section shows the dedicated CAN Receive Buffer
registers with their associated control registers.
REGISTER 27-13: RXB0CON: RECEIVE BUFFER 0 CONTROL REGISTER
DS39977C-page 410
Mode 0
Mode 1,2
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6,6-5
bit 5
bit 4
bit 3
Note 1:
2:
This bit is set by the CAN module upon receiving a message and must be cleared by software after the
buffer is read. As long as RXFUL is set, no new message will be loaded and the buffer will be considered
full. After clearing the RXFUL flag, the PIR5 bit, RXB0IF, can be cleared. If RXB0IF is cleared, but RXFUL
is not cleared, then RXB0IF is set again.
This bit allows the same filter jump table for both RXB0CON and RXB1CON.
DEDICATED CAN RECEIVE
BUFFER REGISTERS
bit 7
RXFUL: Receive Full Status bit
1 = Receive buffer contains a received message
0 = Receive buffer is open to receive a new message
Mode 0:
RXM<1:0>: Receive Buffer Mode bit 1 (combines with RXM0 to form RXM<1:0> bits, see bit 5)
11 = Receive all messages (including those with errors); filter criteria is ignored
10 = Receive only valid messages with extended identifier; EXIDEN in RXFnSIDL must be ‘ 1 ’
01 = Receive only valid messages with standard identifier; EXIDEN in RXFnSIDL must be ‘ 0 ’
00 = Receive all valid messages as per the EXIDEN bit in the RXFnSIDL register
Mode 1, 2:
RXM1 : Receive Buffer Mode bit 1
1 = Receive all messages (including those with errors); acceptance filters are ignored
0 = Receive all valid messages as per acceptance filters
Mode 0:
RXM0: Receive Buffer Mode bit 0 (combines with RXM1 to form RXM<1:0>bits, see bit 6)
Mode 1, 2:
RTRRO: Remote Transmission Request bit for Received Message (read-only)
1 = A remote transmission request is received
0 = A remote transmission request is not received
Mode 0:
Unimplemented: Read as ‘ 0 ’
Mode 1, 2:
FILHIT<4:0>: Filter Hit bit 4
This bit combines with other bits to form filter acceptance bits<4:0>.
Mode 0:
RXRTRRO: Remote Transmission Request bit for Received Message (read-only)
1 = A remote transmission request is received
0 = A remote transmission request is not received
Mode 1, 2:
FILHIT<4:0>: Filter Hit bit 3
This bit combines with other bits to form filter acceptance bits<4:0>.
RXFUL
RXFUL
R/C-0
R/C-0
(1)
(1)
R/W-0
R/W-0
RXM1
RXM1
C = Clearable bit
W = Writable bit
‘1’ = Bit is set
RTRRO
R/W-0
RXM0
(1)
R-0
Preliminary
FILHITF4
U-0
R-0
—
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
RXRTRRO RXB0DBEN
FILHIT3
R-0
R-0
FILHIT2
R/W-0
R-0
 2011 Microchip Technology Inc.
x = Bit is unknown
JTOFF
FILHIT1
R-0
R-0
(2)
FILHIT0
FILHIT0
R-0
R-0
bit 0