ATSAM3X4EA-AU Atmel, ATSAM3X4EA-AU Datasheet - Page 932
ATSAM3X4EA-AU
Manufacturer Part Number
ATSAM3X4EA-AU
Description
ARM Microcontrollers - MCU QFP144,GREEN, IND TEMP, MRL A
Manufacturer
Atmel
Datasheet
1.ATSAM3X8EA-AU.pdf
(1467 pages)
Specifications of ATSAM3X4EA-AU
Rohs
yes
Core
ARM Cortex M3
Processor Series
SAM3X
Data Bus Width
32 bit
Maximum Clock Frequency
84 MHz
Program Memory Size
256 KB
Data Ram Size
64 KB
On-chip Adc
Yes
Operating Supply Voltage
2.4 V to 3.6 V
Operating Temperature Range
- 40 C to +85 C
Package / Case
LQFP-144
Mounting Style
SMD/SMT
Factory Pack Quantity
60
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 932 of 1467
- Download datasheet (8Mb)
38.8.2
38.8.3
932
932
SAM3X/A
SAM3X/A
Data Transfer Operation
Read Operation
The High Speed MultiMedia Card allows several read/write operations (single block, multiple
blocks, stream, etc.). These kinds of transfer can be selected setting the Transfer Type (TRTYP)
field in the HSMCI Command Register (HSMCI_CMDR).
These operations can be done using the features of the DMA Controller.
In all cases, the block length (BLKLEN field) must be defined either in the mode register
HSMCI_MR, or in the Block Register HSMCI_BLKR. This field determines the size of the data
block.
Consequent to MMC Specification 3.1, two types of multiple block read (or write) transactions
are defined (the host can use either one at any time):
The following flowchart
DMAC facilities. In this example, a polling method is used to wait for the end of read. Similarly,
the user can configure the interrupt enable register (HSMCI_IER) to trigger an interrupt at the
end of read.
• Open-ended/Infinite Multiple block read (or write):
• Multiple block read (or write) with pre-defined block count (since version 3.1 and higher):
The number of blocks for the read (or write) multiple block operation is not defined. The card
will continuously transfer (or program) data blocks until a stop transmission command is
received.
The card will transfer (or program) the requested number of data blocks and terminate the
transaction. The stop command is not required at the end of this type of multiple block read
(or write), unless terminated with an error. In order to start a multiple block read (or write)
with pre-defined block count, the host must correctly program the HSMCI Block Register
(HSMCI_BLKR). Otherwise the card will start an open-ended multiple block read. The BCNT
field of the Block Register defines the number of blocks to transfer (from 1 to 65535 blocks).
Programming the value 0 in the BCNT field corresponds to an infinite block transfer.
(Figure
38-9) shows how to read a single block with or without use of
11057B–ATARM–28-May-12
11057B–ATARM–28-May-12
Related parts for ATSAM3X4EA-AU
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Development Boards & Kits - ARM EVAL KIT SAM3X & SAM3A series
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: