DS26514G Maxim Integrated, DS26514G Datasheet - Page 20

• Manufacturer Part Number: DS26514G
• Description: Network Controller & Processor ICs
• Manufacturer: Maxim Integrated

Specifications of DS26514G

• Part # Aliases: 90-26514-G00

8.
8.1
Table 8-1. Detailed Pin Descriptions
19-5856; Rev 4; 5/11
TXENABLE/
SCAN_EN
RESREF
RRING1
RRING2
RRING3
RRING4
TRING1
TRING2
TRING3
TRING4
NAME
RTIP1
RTIP2
RTIP3
RTIP4
TTIP1
TTIP2
TTIP3
TTIP4
PIN DESCRIPTIONS
Pin Functional Description
G3, H3
A1, A2
H1, H2
A3, B3
R3, T3
T1, T2
J3, K3
J1 J2
PIN
L13
C1
F1
P1
C2
F2
P2
L1
L2
J5
Impedance
Impedance
Output,
Output,
Analog
Analog
Analog
Analog
TYPE
Input
Input
Input
Input
High
High
Transmit Bipolar Tip for Transceiver 1 to 4. These pins are differential line
driver tip outputs. These pins can be high impedance if:
If TXENABLE is low, TTIPn/TRINGn will be high impedance. Note that if
TXENABLE is low, the register settings for control of TTIPn/TRINGn are ignored
and output is high impedance.
The differential outputs of TTIPn and TRINGn can provide internal matched
impedance for E1 75Ω, E1 120Ω, T1 100Ω, or J1 110Ω. The user can turn off
internal termination.
Note: The two pins shown for each transmit bipolar tip (e.g., pins A1 and A2 for
TTIP1) should be tied together.
Transmit Bipolar Ring for Transceiver 1 to 4. These pins are differential line
driver ring outputs. These pins can be high impedance if:
If TXENABLE is low, TTIPn/TRINGn will be high impedance. Note that if
TXENABLE is low, the register settings for control of TTIPn/TRINGn are ignored
and output is high impedance.
The differential outputs of TTIPn and TRINGn can provide internal matched
impedance for E1 75Ω, E1 120Ω, T1 100Ω, or J1 110Ω. The user can turn off
internal termination.
Note: The two pins shown for each transmit bipolar ring (e.g., pins A3 and B3 for
TRING1) should be tied together.
Transmit Enable. If this pin is pulled low, all transmitter outputs (TTIPn and
TRINGn) are high impedance. The register settings for three-state control of
TTIPn/TRINGn are ignored if TXENABLE is low. If TXENABLE is high, the
particular driver can be three-stated by the register settings.
Scan Enable. When low, device is in normal operation. Scan enable is selected
by the SCANMODE pin. Note: User should not select scan enable—test mode
only.
Receive Bipolar Tip for Transceiver 1 to 4. The differential inputs of RTIPn
and RRINGn can provide internal matched impedance for E1 75Ω, E1 120Ω, T1
100Ω, or J1 110Ω. The user can turn off internal termination via the LIU Receive
Impedance and Sensitivity Monitor register (LRISMR).
Receive Bipolar Ring for Transceiver 1 to 4. The differential inputs of RTIPn
and RRINGn can provide internal matched impedance for E1 75Ω, E1 120Ω, T1
100Ω, or J1 110Ω. The user has the option of turning off internal termination via
the LIU Receive Impedance and Sensitivity Monitor register (LRISMR).
Resistor Reference. This pin is used to calibrate the internal impedance match
resistors of the receive LIUs. This pin should be tied to V
resistor.
ANALOG TRANSMIT
ANALOG RECEIVE
FUNCTION
DS26514 4-Port T1/E1/J1 Transceiver
SS
through a 10kΩ ±1%
20 of 305