N25Q128A13BSF40F NUMONYX, N25Q128A13BSF40F Datasheet - Page 54

• Manufacturer Part Number: N25Q128A13BSF40F
• Description: IC SRL FLASH 128MB NMX 16-SOIC
• Manufacturer: NUMONYX
• Series: Forté™r

Specifications of N25Q128A13BSF40F

• Format - Memory: FLASH
• Memory Type: FLASH
• Memory Size: 128M (16M x 8)
• Speed: 108MHz
• Interface: SPI, 3-Wire Serial
• Voltage - Supply: 2.7 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Instructions
9
Note:
9.1
54/157
Instructions
The device can work in three different protocols: Extended SPI, DIO-SPI and QIO-SPI.
Each protocol has a dedicated instruction set, and each instruction set features the same
functionality:
The application can choose in every time of the device life which protocol to use by setting
the dedicated bits either in the Non Volatile Configuration Register or the Volatile Enhanced
Configuration Register.
In multiple SPI protocols, all instructions, addresses, and data are parallel on two lines (DIO-
SPI protocol) or four lines (QIO-SPI protocol).
All instructions, addresses and data are shifted in and out of the device, most significant bit
first.
Serial Data input(s) is (are) sampled on the first rising edge of Serial Clock (C) after Chip
Select (S) is driven Low. Then, the one-byte instruction code must be shifted in to the
device, most significant bit first, on Serial Data input(s), each bit being latched on the rising
edges of Serial Clock (C). Instruction code is shifted into the device just on DQ0 in Extended
SPI protocol, on DQ0 and DQ1 in DIO-SPI protocol and on DQ0, DQ1, DQ2, and DQ3 in
QIO-SPI protocol.
In standard mode every instruction sequence starts with a one-byte instruction code.
Depending on the instruction, this might be followed by address bytes, or by data bytes, or
by both or none.
In XIP modes only read operation and exit XIP mode can be performed, and to read the
memory content no instructions code are needed: the device directly receives addresses
and after a configurable number of dummy clock cycles it outputs the required data.
Extended SPI Instructions
In Extended SPI protocol instruction set the instruction code is always shifted into the device
just on DQ0 pin, while depending on the instruction addresses and input/output data can run
on single, two or four wires.
In the case of a Read Instructions Data Bytes (READ), Read Data Bytes at Higher Speed
(FAST_READ), Dual Output Fast Read (DOFR), Dual Input/Output Fast Read (DIOFR),
Quad Output Fast Read (QOFR), Quad Input/Output Fast Read (QIOFR), Read OTP
(ROTP), Read Lock Registers (RDLR), Read Status Register (RDSR), Read Flag Status
Register (RFSR), Read NV Configuration Register (RDNVCR), Read Volatile Configuration
Register (RDVCR), Read Volatile Enhanced Configuration Register (RDVECR) and Read
Identification (RDID) instruction, the shifted-in instruction sequence is followed by a data-out
Read, program and erase the memory and the 64 byte OTP area,
Suspend and resume the program or erase operations,
Read Serial Flash Discovery Parameter area (SFDP)
Read and modify all the registers and to read the device ID: please note that in this
case there is a small functionality difference among the single and the multiple I/O read
ID instructions. See
Section 9.3.1: Multiple I/O Read Identification
Section 9.2.1: Multiple I/O Read Identification protocol
Micron Technology, Inc., reserves the right to change products or specifications without notice.
(MIORDID).
©2010 Micron Technology, Inc. All rights reserved.
N25Q128 - 3 V
and