Z16F2800100ZCOG Zilog, Z16F2800100ZCOG Datasheet - Page 319
Z16F2800100ZCOG
Manufacturer Part Number
Z16F2800100ZCOG
Description
DEV KIT FOR Z16F ZNEO
Manufacturer
Zilog
Series
ZNEO™r
Type
MCUr
Datasheets
1.Z16F2800100ZCOG.pdf
(2 pages)
2.Z16F2800100ZCOG.pdf
(30 pages)
3.Z16F2800100ZCOG.pdf
(388 pages)
Specifications of Z16F2800100ZCOG
Contents
Evaluation Board, Software and Documentation
For Use With/related Products
Z16F Series
For Use With
269-4661 - KIT ACC ETHERNET SMART CABLE
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
269-4537
- Current page: 319 of 388
- Download datasheet (22Mb)
Table 165. OCD Baud Rate Limits (Continued)
PS022008-0810
System Clock
Frequency
32.768 kHz
*
The maximum baud rate is limited by the rise and fall times due to the cable impedance.
Auto-Baud Detector
Line Control
To operate using various clock frequencies over a range of baud rates, the serial interface
has an auto-baud detector. The auto-baud detector is used to automatically setup the baud
rate generator.
The auto-baud detector is setup to measure one of two different auto-baud characters,
80H
Z8 Encore!
as a UART, you can switch to an auto-baud character of
ASCII carriage return character and is sent using a terminal interface.
When using the auto-baud character
the falling edge at the beginning of the start bit to the rising edge at the beginning of data
bit 7. For the auto-baud character
the rising edge at the end of the start bit to the rising edge at the beginning of the stop bit.
This measured value is automatically written to the BRG reload register once the
auto-baud character is received. Once configured, the BRG will generate a bit clock based
on this measured character time.
When operating at high speeds, it is appropriate to speed up the rise and fall times of the
single wire bus. Three control bits are used to control the bus rise and fall times, the high
drive strength enable bit, the drive high enable bit, and the output enable control bit.
The high drive strength enable bit puts the pin into high drive mode. For information on
high drive strength, see
If the output enable control bit is set, the line is driven High and Low during transmission.
If the drive high control bit is set, it drives the line high for short periods when transmit-
ting a logic one. This rapidly charges the inherent capacitance of the single wire bus.
If both the output enable and drive high control bits are set, the line is driven high for one
clock cycle when transmitting a one. If the output enable bit is clear and the drive high bit
is set, the line is driven high until the input is detected High or the center of the bit time
occurs, whichever is first.
(default) or
®
debug interfaces. When the OCD is disabled and the DBG pin is being used
0DH
Baud Rate
4096 baud
Maximum
. The default auto-baud character
Electrical Characteristics
P R E L I M I N A R Y
0DH
80H
, the auto-baud detector measures the period from
Minimum Baud Rate
, the auto-baud detector measures the period from
(OCDEN=0)
4.0 baud
on page 337.
80H
0DH
is compatible with previous
. The
Product Specification
Minimum Baud Rate
0DH
ZNEO
(OCDEN=1)
character is the
On-Chip Debugger
64 baud
Z16F Series
303
Related parts for Z16F2800100ZCOG
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Communication Controllers, ZILOG INTELLIGENT PERIPHERAL CONTROLLER (ZIP)
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
KIT DEV FOR Z8 ENCORE 16K TO 64K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 8K/4K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 4K TO 8K
Manufacturer:
Zilog
Datasheet:
Part Number:
Description:
CMOS Z8 microcontroller. ROM 16 Kbytes, RAM 256 bytes, speed 16 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Low-cost microcontroller. 512 bytes ROM, 61 bytes RAM, 8 MHz
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Z8 4K OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
CMOS SUPER8 ROMLESS MCU
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
OTP (KB) = 1, RAM = 125, Speed = 12, I/O = 14, 8-bit Timers = 2, Comm Interfaces Other Features = Por, LV Protect, Voltage = 4.5-5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Zilog, Inc.
Datasheet: