DSP56309EVM Freescale Semiconductor, DSP56309EVM Datasheet - Page 85

KIT EVALUATION FOR XC56309

DSP56309EVM

Manufacturer Part Number
DSP56309EVM
Description
KIT EVALUATION FOR XC56309
Manufacturer
Freescale Semiconductor
Type
DSPr
Datasheets

Specifications of DSP56309EVM

Contents
Module Board, Installation Guide, Power Supply, Cable, Software and more
Description/function
Audio DSPs
Product
Audio Modules
For Use With/related Products
DSP56309
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Freescale Semiconductor
Number
Bit
7
6
5
4
3
2
Bit Name
BPAC
BYEN
BXEN
BPEN
BAAP
Table 4-10. Address Attribute Registers (AAR[0–3]) Bit Definitions
Reset
Value
0
0
0
0
0
0
Bus Packing Enable
Enables/disables the internal packing/unpacking logic. When BPAC is set, packing is
enabled. In this mode each DMA external access initiates three external accesses to an
8-bit wide external memory (the addresses for these accesses are DAB, then DAB + 1 and
then DAB + 2). Packing to a 24-bit word (or unpacking from a 24-bit word to three 8-bit
words) is done automatically by the expansion port control hardware. The external memory
should reside in the eight Least Significant Bits (LSBs) of the external data bus, and the
packing (or unpacking for external write accesses) occurs in “Little Endian” order (that is,
the low byte is stored in the lowest of the three memory locations and is transferred first; the
middle byte is stored/transferred next; and the high byte is stored/transferred last). When
this bit is cleared, the expansion port control logic assumes a 24-bit wide external memory.
Notes: 1.
Reserved. Write to 0 for future compatibility.
Bus Y Data Memory Enable
A read/write control bit that enables/disables the AA pin and logic during external Y data
space accesses. When set, BYEN enables the comparison of the external address to the
BAC bits during external Y data space accesses. If BYEN is cleared, no address
comparison is performed.
Bus X Data Memory Enable
A read/write control bit that enables/disables the AA pin and logic during external X data
space accesses. When set, BXEN enables the comparison of the external address to the
BAC bits during external X data space accesses. If BXEN is cleared, no address
comparison is performed.
Bus Program Memory Enable
A read/write control bit that enables/disables the AA/RAS pin and logic during external
program space accesses. When set, BPEN enables the comparison of the external address
to the BAC bits during external program space accesses. If BPEN is cleared, no address
comparison is performed.
Bus Address Attribute Polarity
A read/write Bus Address Attribute Polarity (BAAP) control bit that defines whether the
AA/RAS signal is active low or active high. When BAAP is cleared, the AA/RAS signal is
active low (useful for enabling memory modules or for DRAM Row Address Strobe). If
BAAP is set, the appropriate AA/RAS signal is active high (useful as an additional address
bit).
2.
3.
4.
DSP56309 User’s Manual, Rev. 1
BPAC is used only for DMA accesses and not core accesses.
To ensure sequential external accesses, the DMA address should advance
three steps at a time in two-dimensional mode with a row length of one and an
offset size of three. For details, refer to the Freescale application note,
APR23/D, Using the DSP56300 Direct Memory Access Controller .
To prevent improper operation, DMA address + 1 and DMA
address + 2 should not cross the AAR bank borders.
Arbitration is not allowed during the packing access (that is, the three
accesses are treated as one access with respect to arbitration, and the bus
mastership is not released during these accesses).
Description
Bus Interface Unit (BIU) Registers
4-27

Related parts for DSP56309EVM