ATTINY4313-MU Atmel, ATTINY4313-MU Datasheet - Page 173

• Manufacturer Part Number: ATTINY4313-MU
• Description: IC MCU AVR 4K FLASH 20QFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY4313-MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 18
• Program Memory Size: 4KB (2K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-VQFN Exposed Pad, 20-HVQFN, 20-SQFN, 20-DHVQFN
• Processor Series: ATtiny
• Core: AVR
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: SPI, USART, USI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 18
• Number Of Timers: 2
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Operating Temperature Range: - 40 C to + 85 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Details

19.3
19.4
8246A–AVR–11/09
Performing a Page Write
Addressing the Flash During Self-Programming
To execute Page Write, set up the address in the Z-pointer, write “00000101” to SPMCSR and
execute SPM within four clock cycles after writing SPMCSR. The data in R1 and R0 is ignored.
The page address must be written to PCPAGE. Other bits in the Z-pointer must be written to
zero during this operation.
Note:
The Z-pointer is used to address the SPM commands.
Since the Flash is organized in pages (see
be treated as having two different sections. One section, consisting of the least significant bits, is
addressing the words within a page, while the most significant bits are addressing the pages.
This is shown in
addressed independently. Therefore it is of major importance that the software addresses the
same page in both the Page Erase and Page Write operation.
The LPM instruction uses the Z-pointer to store the address. Since this instruction addresses the
Flash byte-by-byte, also the LSB (bit Z0) of the Z-pointer is used.
Figure 19-1. Addressing the Flash During SPM
Note:
Bit
ZH (R31)
ZL (R30)
Z - REGISTER
The CPU is halted during the Page Write operation.
The different variables used in
PROGRAM MEMORY
BIT
Z15
PAGE
15
Z7
PROGRAM
COUNTER
7
15
Figure
PAGE ADDRESS
WITHIN THE FLASH
Z14
ZPCMSB
Z6
PCMSB
14
6
19-1. Note that the Page Erase and Page Write operations are
PCPAGE
Z13
13
Z5
5
Figure 19-1
Z12
12
Z4
4
ZPAGEMSB
PAGEMSB
Table 20-7 on page
PCWORD
are listed in
WORD ADDRESS
WITHIN A PAGE
Z11
(Note:)
11
Z3
3
1
0
0
INSTRUCTION WORD
Z10
10
Z2
Table 20-7 on page
2
PAGE
181), the Program Counter can
Z9
Z1
9
1
Z8
Z0
8
0
PCWORD[PAGEMSB:0]:
181.
00
01
02
PAGEEND
173