PIC17LC756A-08/L Microchip Technology, PIC17LC756A-08/L Datasheet - Page 139

• Manufacturer Part Number: PIC17LC756A-08/L
• Description: IC MCU OTP 16KX16 A/D 68PLCC
• Manufacturer: Microchip Technology
• Series: PIC® 17Cr

Specifications of PIC17LC756A-08/L

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 50
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: OTP
• Ram Size: 902 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 68-PLCC
• Processor Series: PIC17LC
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 902 B
• Interface Type: I2C, MSSP, RS- 232, SCI, SPI, USART
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 50
• Number Of Timers: 8
• Operating Supply Voltage: 3 V to 5.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: 0 C
• On-chip Adc: 12 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

15.1.4
The master can initiate the data transfer at any time
because it controls the SCK. The master determines
when the slave (Processor 2, Figure 15-5) is to broad-
cast data by the software protocol.
In Master mode, the data is transmitted/received as
soon as the SSPBUF register is written to. If the SPI is
only going to receive, the SDO output could be dis-
abled (programmed as an input). The SSPSR register
will continue to shift in the signal present on the SDI pin
at the programmed clock rate. As each byte is
received, it will be loaded into the SSPBUF register as
if a normal received byte (interrupts and status bits
appropriately set). This could be useful in receiver
applications as a “Line Activity Monitor” mode.
The clock polarity is selected by appropriately program-
ming bit CKP (SSPCON1<4>). This then, would give
waveforms for SPI communication as shown in
FIGURE 15-6:
2000 Microchip Technology Inc.
Write to
SSPBUF
SCK
(CKP = 0
CKE = 0)
SCK
(CKP = 1
CKE = 0)
SCK
(CKP = 0
CKE = 1)
SCK
(CKP = 1
CKE = 1)
SDO
(CKE = 0)
SDO
(CKE = 1)
SDI
(SMP = 0)
Input
Sample
(SMP = 0)
SDI
(SMP = 1)
Input
Sample
(SMP = 1)
SSPIF
SSPSR to
SSPBUF
MASTER MODE
SPI MODE WAVEFORM (MASTER MODE)
bit7
bit7
bit7
bit7
bit6
bit6
bit5
bit5
bit4
bit4
Figure 15-6, Figure 15-8 and Figure 15-9, where the
MSb is transmitted first. In Master mode, the SPI clock
rate (bit rate) is user programmable to be one of the
following:
• F
• F
• F
• Timer2 output/2
This allows a maximum bit clock frequency (at 33 MHz)
of 8.25 MHz.
Figure 15-6 shows the waveforms for Master mode.
When CKE = 1, the SDO data is valid before there is a
clock edge on SCK. The change of the input sample is
shown based on the state of the SMP bit. The time
when the SSPBUF is loaded with the received data is
shown.
bit3
bit3
OSC
OSC
OSC
/4 (or T
/16 (or 4 • T
/64 (or 16 • T
bit2
bit2
CY
)
bit1
bit1
CY
CY
)
)
PIC17C7XX
bit0
bit0
bit0
bit0
DS30289B-page 139
Next Q4 cycle
after Q2
4 clock
modes