AT91SAM7X256B-AU Atmel, AT91SAM7X256B-AU Datasheet - Page 119

• Manufacturer Part Number: AT91SAM7X256B-AU
• Description: IC MCU 256KB FLASH 100LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7X256B-AU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: CAN, Ethernet, I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Package: 100LQFP
• Device Core: ARM7TDMI
• Family Name: 91S
• Maximum Speed: 55 MHz
• Operating Supply Voltage: 1.8|3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 62
• Interface Type: CAN/Ethernet/SPI/I2S/TWI/USART/USB
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 3
• Controller Family/series: AT91SAM7xxxxx
• No. Of I/o's: 62
• Ram Memory Size: 64KB
• Cpu Speed: 55MHz
• No. Of Timers: 1
• Rohs Compliant: Yes
• Cpu Family: 91S
• Device Core Size: 32b
• Frequency (max): 55MHz
• Total Internal Ram Size: 64KB
• # I/os (max): 62
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 1.8/3.3V
• Operating Supply Voltage (max): 1.95/3.6V
• Operating Supply Voltage (min): 1.65/3V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

20. Fast Flash Programming Interface (FFPI)
20.1
20.2
20.2.1
6120H–ATARM–17-Feb-09
Overview
Parallel Fast Flash Programming
Device Configuration
The Fast Flash Programming Interface provides two solutions - parallel or serial - for high-vol-
ume programming using a standard gang programmer. The parallel interface is fully
handshaked and the device is considered to be a standard EEPROM. Additionally, the parallel
protocol offers an optimized access to all the embedded Flash functionalities. The serial inter-
face uses the standard IEEE 1149.1 JTAG protocol. It offers an optimized access to all the
embedded Flash functionalities.
Although the Fast Flash Programming Mode is a dedicated mode for high volume programming,
this mode not designed for in-situ programming.
In Fast Flash Programming Mode, the device is in a specific test mode. Only a certain set of pins
is significant, the rest of the PIOs are used as inputs with a pull-up. The crystal oscillator is in
bypass mode. Other pins must be left unconnected.
Figure 20-1. Parallel Programming Interface
MODE[3:0]
DATA[15:0]
0 - 50MHz
NVALID
VDDIO
VDDIO
VDDIO
NCMD
NOE
RDY
AT91SAM7X512/256/128 Preliminary
PGMD[15:0]
TST
PGMEN0
PGMEN1
PGMNCMD
PGMRDY
PGMNOE
PGMNVALID
PGMM[3:0]
XIN
VDDCORE
VDDIO
VDDPLL
VDDFLASH
GND
119