AT91SAM7X256B-AU Atmel, AT91SAM7X256B-AU Datasheet - Page 583

• Manufacturer Part Number: AT91SAM7X256B-AU
• Description: IC MCU 256KB FLASH 100LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7X256B-AU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: CAN, Ethernet, I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Package: 100LQFP
• Device Core: ARM7TDMI
• Family Name: 91S
• Maximum Speed: 55 MHz
• Operating Supply Voltage: 1.8|3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 62
• Interface Type: CAN/Ethernet/SPI/I2S/TWI/USART/USB
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 3
• Controller Family/series: AT91SAM7xxxxx
• No. Of I/o's: 62
• Ram Memory Size: 64KB
• Cpu Speed: 55MHz
• No. Of Timers: 1
• Rohs Compliant: Yes
• Cpu Family: 91S
• Device Core Size: 32b
• Frequency (max): 55MHz
• Total Internal Ram Size: 64KB
• # I/os (max): 62
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 1.8/3.3V
• Operating Supply Voltage (max): 1.95/3.6V
• Operating Supply Voltage (min): 1.65/3V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

• CLK: MDC clock divider
Set according to system clock speed. This determines by what number system clock is divided to generate MDC.
For conformance with 802.3, MDC must not exceed 2.5MHz (MDC is only active during MDIO read and write operations).
• RTY: Retry test
Must be set to zero for normal operation. If set to one, the back off between collisions is always one slot time. Setting this
bit to one helps testing the too many retries condition. Also used in the pause frame tests to reduce the pause counters
decrement time from 512 bit times, to every rx_clk cycle.
• PAE: Pause Enable
When set, transmission pauses when a valid pause frame is received.
• RBOF: Receive Buffer Offset
Indicates the number of bytes by which the received data is offset from the start of the first receive buffer.
• RLCE: Receive Length field Checking Enable
When set, frames with measured lengths shorter than their length fields are discarded. Frames containing a type ID in
bytes 13 and 14 — length/type ID = 0600 — are not be counted as length errors.
• DRFCS: Discard Receive FCS
When set, the FCS field of received frames are not be copied to memory.
• EFRHD:
Enable Frames to be received in half-duplex mode while transmitting.
• IRXFCS: Ignore RX FCS
When set, frames with FCS/CRC errors are not rejected and no FCS error statistics are counted. For normal operation, this
bit must be set to 0.
6120H–ATARM–17-Feb-09
RBOF
CLK
00
01
10
11
00
01
10
11
MDC
MCK divided by 8 (MCK up to 20 MHz)
MCK divided by 16 (MCK up to 40 MHz)
MCK divided by 32 (MCK up to 80 MHz)
MCK divided by 64 (MCK up to 160 MHz)
Offset
No offset from start of receive buffer
One-byte offset from start of receive buffer
Two-byte offset from start of receive buffer
Three-byte offset from start of receive buffer
AT91SAM7X512/256/128 Preliminary
583