AT91SAM7X256B-AU Atmel, AT91SAM7X256B-AU Datasheet - Page 518

• Manufacturer Part Number: AT91SAM7X256B-AU
• Description: IC MCU 256KB FLASH 100LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7X256B-AU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: CAN, Ethernet, I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Package: 100LQFP
• Device Core: ARM7TDMI
• Family Name: 91S
• Maximum Speed: 55 MHz
• Operating Supply Voltage: 1.8|3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 62
• Interface Type: CAN/Ethernet/SPI/I2S/TWI/USART/USB
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 3
• Controller Family/series: AT91SAM7xxxxx
• No. Of I/o's: 62
• Ram Memory Size: 64KB
• Cpu Speed: 55MHz
• No. Of Timers: 1
• Rohs Compliant: Yes
• Cpu Family: 91S
• Device Core Size: 32b
• Frequency (max): 55MHz
• Total Internal Ram Size: 64KB
• # I/os (max): 62
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 1.8/3.3V
• Operating Supply Voltage (max): 1.95/3.6V
• Operating Supply Voltage (min): 1.65/3V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

36.6.5
36.6.5.1
6120H–ATARM–17-Feb-09
Low-power Mode
Enabling Low-power Mode
Reactive overload frames are automatically handled by the CAN controller even if the OVL bit in
the CAN_MR register is not set. An overload flag is generated in the same way as an error flag,
but error counters do not increment.
In Low-power Mode, the CAN controller cannot send or receive messages. All mailboxes are
inactive.
In Low-power Mode, the SLEEP signal in the CAN_SR register is set; otherwise, the WAKEUP
signal in the CAN_SR register is set. These two fields are exclusive except after a CAN control-
ler reset (WAKEUP and SLEEP are stuck at 0 after a reset). After power-up reset, the Low-
power Mode is disabled and the WAKEUP bit is set in the CAN_SR register only after detection
of 11 consecutive recessive bits on the bus.
A software application can enable Low-power Mode by setting the LPM bit in the CAN_MR
global register. The CAN controller enters Low-power Mode once all pending transmit messages
are sent.
When the CAN controller enters Low-power Mode, the SLEEP signal in the CAN_SR register is
set. Depending on the corresponding mask in the CAN_IMR register, an interrupt is generated
while SLEEP is set.
The SLEEP signal in the CAN_SR register is automatically cleared once WAKEUP is set. The
WAKEUP signal is automatically cleared once SLEEP is set.
Reception is disabled while the SLEEP signal is set to one in the CAN_SR register. It is impor-
tant to note that those messages with higher priority than the last message transmitted can be
received between the LPM command and entry in Low-power Mode.
Once in Low-power Mode, the CAN controller clock can be switched off by programming the
chip’s Power Management Controller (PMC). The CAN controller drains only the static current.
Error counters are disabled while the SLEEP signal is set to one.
Thus, to enter Low-power Mode, the software application must:
Now the CAN Controller clock can be disabled. This is done by programming the Power Man-
agement Controller (PMC).
– Set LPM field in the CAN_MR register
– Wait for SLEEP signal rising
AT91SAM7X512/256/128 Preliminary
518