AT91SAM7X256B-AU Atmel, AT91SAM7X256B-AU Datasheet - Page 507

• Manufacturer Part Number: AT91SAM7X256B-AU
• Description: IC MCU 256KB FLASH 100LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7X256B-AU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: CAN, Ethernet, I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Package: 100LQFP
• Device Core: ARM7TDMI
• Family Name: 91S
• Maximum Speed: 55 MHz
• Operating Supply Voltage: 1.8|3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 62
• Interface Type: CAN/Ethernet/SPI/I2S/TWI/USART/USB
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 3
• Controller Family/series: AT91SAM7xxxxx
• No. Of I/o's: 62
• Ram Memory Size: 64KB
• Cpu Speed: 55MHz
• No. Of Timers: 1
• Rohs Compliant: Yes
• Cpu Family: 91S
• Device Core Size: 32b
• Frequency (max): 55MHz
• Total Internal Ram Size: 64KB
• # I/os (max): 62
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 1.8/3.3V
• Operating Supply Voltage (max): 1.95/3.6V
• Operating Supply Voltage (min): 1.65/3V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

36.3
36.4
Table 36-1.
36.5
36.5.1
36.5.2
36.5.3
6120H–ATARM–17-Feb-09
Name
CANRX
CANTX
Application Block Diagram
I/O Lines Description
Product Dependencies
I/O Lines
Power Management
Interrupt
I/O Lines Description
Description
CAN Receive Serial Data
CAN Transmit Serial Data
Figure 36-2.
The pins used for interfacing the CAN may be multiplexed with the PIO lines. The programmer
must first program the PIO controller to assign the desired CAN pins to their peripheral function.
If I/O lines of the CAN are not used by the application, they can be used for other purposes by
the PIO Controller.
The programmer must first enable the CAN clock in the Power Management Controller (PMC)
before using the CAN.
A Low-power Mode is defined for the CAN controller: If the application does not require CAN
operations, the CAN clock can be stopped when not needed and be restarted later. Before stop-
ping the clock, the CAN Controller must be in Low-power Mode to complete the current transfer.
After restarting the clock, the application must disable the Low-power Mode of the CAN
controller.
The CAN interrupt line is connected on one of the internal sources of the Advanced Interrupt
Controller. Using the CAN interrupt requires the AIC to be programmed first. Note that it is not
recommended to use the CAN interrupt line in edge-sensitive mode.
Application Block Diagram
CAN-based Application Layer
AT91SAM7X512/256/128 Preliminary
CAN Data Link Layer
CAN-based Profiles
CAN Physical Layer
Layers
Implementation
CAN Controller
Transceiver
Software
Software
Type
Input
Output
507