AT91SAM7X256B-AU Atmel, AT91SAM7X256B-AU Datasheet - Page 619

• Manufacturer Part Number: AT91SAM7X256B-AU
• Description: IC MCU 256KB FLASH 100LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7X256B-AU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: CAN, Ethernet, I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Package: 100LQFP
• Device Core: ARM7TDMI
• Family Name: 91S
• Maximum Speed: 55 MHz
• Operating Supply Voltage: 1.8|3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 62
• Interface Type: CAN/Ethernet/SPI/I2S/TWI/USART/USB
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 3
• Controller Family/series: AT91SAM7xxxxx
• No. Of I/o's: 62
• Ram Memory Size: 64KB
• Cpu Speed: 55MHz
• No. Of Timers: 1
• Rohs Compliant: Yes
• Cpu Family: 91S
• Device Core Size: 32b
• Frequency (max): 55MHz
• Total Internal Ram Size: 64KB
• # I/os (max): 62
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 1.8/3.3V
• Operating Supply Voltage (max): 1.95/3.6V
• Operating Supply Voltage (min): 1.65/3V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

38.3.2
6120H–ATARM–17-Feb-09
Peripheral Power Consumption in Active Mode
These figures represent the power consumption typically measured on the power supplies..
Table 38-6.
Notes:
Table 38-7.
Note:
Mode
Active
(AT91SAM7X512/256/128)
Ultra Low Power
Peripheral
PIO Controller
USART
UDP
PWM
TWI
SPI
SSC
Timer Counter Channels
CAN
ARM7TDMI
EMAC
System Peripherals
(AT91SAM7X512/256/128)
1. “Flash is in standby mode”, means the Flash is not accessed at all.
2. Low power consumption figures stated above cannot be guaranteed when accesing the Flash
1. Note: V
in Ultra Low Power mode. In order to meet given low power consumption figures, it is recom-
mended to either stop the processor or jump to SRAM.
Power Consumption for Different Modes
Power Consumption on V
(2)
DDCORE
= 1.85V, T
AT91SAM7X512/256/128 Preliminary
Conditions
Voltage regulator is on.
Brown Out Detector is activated.
Flash is read.
ARM Core clock is 50MHz.
Analog-to-Digital Converter activated.
All peripheral clocks activated.
USB transceiver enabled.
onto AMP1
onto AMP2
Voltage regulator is in Low-power mode.
Brown Out Detector is de-activated.
Flash is in standby mode.
ARM Core in idle mode.
MCK @ 500Hz.
Analog-to-Digital Converter de-activated.
All peripheral clocks de-activated.
USB transceiver disabled.
DDM and DDP pins connected to ground.
onto AMP1
onto AMP2
A
= 25° C
DDCORE
(1)
Consumption (Typ)
(1)
160
120
200
12
28
20
16
16
32
75
5
6
Consumption
44
43
26
12
µA/MHz
Unit
Unit
mA
µA
619