MC9S12XA256CAL Freescale Semiconductor, MC9S12XA256CAL Datasheet - Page 107

• Manufacturer Part Number: MC9S12XA256CAL
• Description: IC MCU 256K FLASH 112-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12XA256CAL

• Core Processor: HCS12X
• Core Size: 16-Bit
• Speed: 80MHz
• Connectivity: EBI/EMI, I²C, IrDA, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 91
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 112-LQFP
• No. Of I/o's: 91
• Eeprom Memory Size: 4KB
• Ram Memory Size: 16KB
• Cpu Speed: 80MHz
• No. Of Timers: 1
• No. Of Pwm Channels: 8
• Digital Ic Case Style: LQFP
• Rohs Compliant: Yes
• Processor Series: S12XA
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 16 KB
• Interface Type: CAN, I2C, SCI, SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 91
• Number Of Timers: 12
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: EVB9S12XDP512E
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2 (10 bit, 16 Channel)
• Package: 112LQFP
• Family Name: HCS12
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 2.5|5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Freescale Semiconductor
CME
0
1
1
1
SCME
X
0
1
1
SCMIE
X
X
0
1
Clock failure -->
Clock failure -->
Clock failure -->
Clock failure -->
SCMIF generates self clock mode wakeup interrupt.
Table 2-12. Outcome of Clock Loss in Wait Mode
Scenario 1: OSCCLK recovers prior to exiting wait mode.
Scenario 2: OSCCLK does not recover prior to exiting wait mode.
No action, clock loss not detected.
CRG performs Clock Monitor Reset immediately
Some time later OSCCLK recovers.
Some time later either a wakeup interrupt occurs (no SCM interrupt)
or an External Reset is applied.
Some time later either a wakeup interrupt occurs (no SCM interrupt)
or an External RESET is applied.
– MCU remains in wait mode,
– VREG enabled,
– PLL enabled,
– SCM activated,
– Start clock quality check,
– Set SCMIF interrupt flag.
– CM no longer indicates a failure,
– 4096 OSCCLK cycles later clock quality check indicates clock o.k.,
– SCM deactivated,
– PLL disabled depending on PLLWAI,
– VREG remains enabled (never gets disabled in wait mode).
– MCU remains in wait mode.
– Exit wait mode using OSCCLK as system clock (SYSCLK),
– Continue normal operation.
– Exit wait mode using OSCCLK as system clock,
– Start reset sequence.
– MCU remains in wait mode,
– VREG enabled,
– PLL enabled,
– SCM activated,
– Start clock quality check,
– Set SCMIF interrupt flag,
– Keep performing clock quality checks (could continue infinitely) while in wait mode.
– Exit wait mode in SCM using PLL clock (f
– Continue to perform additional clock quality checks until OSCCLK is o.k. again.
– Exit wait mode in SCM using PLL clock (f
– Start reset sequence,
– Continue to perform additional clock quality checks until OSCCLKis o.k.again.
– VREG enabled,
– PLL enabled,
– SCM activated,
– Start clock quality check,
– SCMIF set.
– Exit wait mode in SCM using PLL clock (f
– Continue to perform a additional clock quality checks until OSCCLK is o.k. again.
MC9S12XDP512 Data Sheet, Rev. 2.21
CRG Actions
Chapter 2 Clocks and Reset Generator (S12CRGV6)
SCM
SCM
SCM
) as system clock,
) as system clock,
) as system clock,
107