MC9S12XA256CAL Freescale Semiconductor, MC9S12XA256CAL Datasheet - Page 566

• Manufacturer Part Number: MC9S12XA256CAL
• Description: IC MCU 256K FLASH 112-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12XA256CAL

• Core Processor: HCS12X
• Core Size: 16-Bit
• Speed: 80MHz
• Connectivity: EBI/EMI, I²C, IrDA, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 91
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 112-LQFP
• No. Of I/o's: 91
• Eeprom Memory Size: 4KB
• Ram Memory Size: 16KB
• Cpu Speed: 80MHz
• No. Of Timers: 1
• No. Of Pwm Channels: 8
• Digital Ic Case Style: LQFP
• Rohs Compliant: Yes
• Processor Series: S12XA
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 16 KB
• Interface Type: CAN, I2C, SCI, SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 91
• Number Of Timers: 12
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: EVB9S12XDP512E
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2 (10 bit, 16 Channel)
• Package: 112LQFP
• Family Name: HCS12
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 2.5|5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Chapter 14 Voltage Regulator (S12VREG3V3V5)
The API Trimming bits APITR[5:0] must be set so the minimum period equals 0.2 ms if stable frequency
is desired.
See
14.4.8
This section describes how VREG_3V3 controls the reset of the MCU.The reset values of registers and
signals are provided in
listed in
14.4.9
14.4.9.1
During chip power-up the digital core may not work if its supply voltage V
deassertion level (V
is kept high until V
The power-on reset is active in all operation modes of VREG_3V3.
14.4.9.2
For details on low-voltage reset, see
14.4.10 Interrupts
This section describes all interrupts originated by VREG_3V3.
The interrupt vectors requested by VREG_3V3 are listed in
priorities are defined at MCU level.
566
Table 14-6
Table
Resets
Description of Reset Operation
Power-On Reset (POR)
Low-Voltage Reset (LVR)
14-9.
The first period after enabling the counter by APIFE might be reduced.
The API internal RC oscillator clock is not available if VREG_3V3 is in
Shutdown Mode.
for the trimming effect of APITR.
DD
PORD
Low-voltage interrupt (LVI)
exceeds V
Section 14.3, “Memory Map and Register
Interrupt Source
). Therefore, signal POR, which forces the other blocks of the device into reset,
Low-voltage reset
Power-on reset
Reset Source
PORD
MC9S12XDP512 Data Sheet, Rev. 2.21
Section 14.4.5, “Low-Voltage Reset
Table 14-10. Interrupt Vectors
. The MCU will run the start-up sequence after POR deassertion.
Table 14-9. Reset Sources
Available only in Full Performance Mode
NOTE
LVIE = 1; available only in Full Performance
Local Enable
Always active
Table
Local Enable
Definition”. Possible reset sources are
14-10. Vector addresses and interrupt
Mode
(LVR)”.
DD
is below the POR
Freescale Semiconductor