M30280FCHP#U5B Renesas Electronics America, M30280FCHP#U5B Datasheet - Page 338

• Manufacturer Part Number: M30280FCHP#U5B
• Description: IC M16C/28 MCU FLASH 128K 80LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/Tiny/28r

Specifications of M30280FCHP#U5B

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, POR, PWM, Voltage Detect, WDT
• Number Of I /o: 71
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 12K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 80-LQFP
• For Use With: R0K330290S000BE - KIT EVAL STARTER FOR M16C/29M30290T2-CPE - EMULATOR COMPACT M16C/26A/28/29M30290T2-CPE-HP - EMULATOR COMPACT FOR M16C/TINY
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

M
R
R
1
e
E
Figure 18.13 Flow Chart of Block Erase Command (when not using erase suspend function)
. v
6
J
18.7.5 Block Erase
0
C
2
9
and ‘xxD0
The FMR00 bit in the FMR0 register indicates whether the auto-erase operation has been completed.
The FMR00 bit is set to “0” (busy) during the auto-erase and “1” (ready) when the auto-erase operation is
completed.
When using the erase-suspend function in EW mode 0, verify whether a flash memory has entered erase
suspend mode, by the FMR46 bit in the FMR4 register. The FMR46 bit is set to “0” during auto-erase
operation and “1” when the auto-erase operation is completed (entering erase-suspend).
After the completion of an auto-erase operation, the FMR07 bit in the FMR0 register indicates whether or
not the auto-erase operation has been successfully completed. (Refer to 18.8.4 Full Status Check).
Also, each block can disable erasing. (Refer to Table 18.4).
Figure 18.13 shows a flow chart of the block erase command programming when not using the erase-
suspend function. Figure 18.14 shows a flow chart of the block erase command programming when
using an erase-suspend function.
In EW mode 1, do not execute this command on the block where the rewrite control program is allocated.
In EW mode 0, the microcomputer enters read status register mode as soon as the auto-erase operation
starts and the status register can be read. The SR7 bit in the status register is set to “0” at the same time
the auto-erase operation starts. This bit is set to “1” when the auto-erase operation is completed. The
microcomputer remains in read status register mode until the read array command is written.
When the erase error occurs, execute the clear status register command and block erase command at
leaset three times until an erase error does not occur.
2 /
Auto erase operation (erase and verify) start in the specified block by writing ‘xx20
0 .
B
8
0
0
0
G
4
J
7
a
o r
0 -
. n
u
2
p
3
0
16
, 1
0
(
M
’ to the highest-order even addresse of a block in the second bus cycle.
NOTES:
2
0
1
0
6
1. Write the command code and data at even address.
2. Refer to Figure 18.15.
3. Execute the clear status register command and block erase command at least 3 times
7
C
until an erase error is not generated when an erase error is generated.
2 /
page 316
, 8
M
1
6
C
2 /
f o
8
3
) B
8
5
Write ‘xxD0
Write command code ‘xx20
Full status check
Block erase completed
block address
16
FMR00=1?
’ to the highest-order
Start
YES
(1)
(2,3)
NO
16
’
(1)
18. Flash Memory Version
16
’ in the first bus cycle