HD64F3337YCP16 Renesas Electronics America, HD64F3337YCP16 Datasheet - Page 106

• Manufacturer Part Number: HD64F3337YCP16
• Description: IC H8 MCU FLASH 60K 84PLCC
• Manufacturer: Renesas Electronics America
• Series: H8® H8/300r

Specifications of HD64F3337YCP16

• Core Processor: H8/300
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: Host Interface, I²C, SCI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 74
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 84-PLCC
• Package: 84PLCC
• Family Name: H8
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 74
• Interface Type: HIF/I2C/SCI
• On-chip Adc: 8-chx10-bit
• On-chip Dac: 2-chx8-bit
• Number Of Timers: 3
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

4.2.3
After a reset, if an interrupt were to be accepted before initialization of the stack pointer (SP: R7),
the program counter and condition code register might not be saved correctly, leading to a
program crash. To prevent this, all interrupts, including NMI, are disabled immediately after a
reset. The first program instruction is therefore always executed. This instruction should initialize
the stack pointer (example: MOV.W #xx:16, SP).
After reset exception handling, in order to initialize the contents of CCR, a CCR manipulation
instruction can be executed before an instruction to initialize the stack pointer. Immediately after
execution of a CCR manipulation instruction, all interrupts including NMI are disabled. Use the
next instruction to initialize the stack pointer.
4.3
4.3.1
The interrupt sources include nine external sources from 23 input pins (NMI, IRQ
KEYIN
chip supporting modules. Table 4.2 lists the interrupt sources in priority order and gives their
vector addresses. When two or more interrupts are requested, the interrupt with highest priority is
served first.
The features of these interrupts are:
74
NMI has the highest priority and is always accepted. All internal and external interrupts except
NMI can be masked by the I bit in the CCR. When the I bit is set to 1, interrupts other than
NMI are not accepted.
IRQ
sensing can be selected for each interrupt individually. NMI is edge-sensed, and either the
rising or falling edge can be selected.
All interrupts are individually vectored. The software interrupt-handling routine does not have
to determine what type of interrupt has occurred.
IRQ
masked individually by user software.
The watchdog timer can generate either an NMI or overflow interrupt, depending on the needs
of the application. For details, see section 11, Watchdog Timer.
0
0
6
to KEYIN
to IRQ
is multiplexed with 8 external sources (KEYIN
Disabling of Interrupts after Reset
Interrupts
Overview
7
can be sensed on the falling edge of the input signal, or level-sensed. The type of
7
), and 26 (H8/3337 Series) or 23 (H8/3397 Series) internal sources in the on-
0
to KEYIN
7
). KEYIN
0
to KEYIN
0
to IRQ
7
7
, and
can be