ATTINY167-15XD Atmel, ATTINY167-15XD Datasheet - Page 164

• Manufacturer Part Number: ATTINY167-15XD
• Description: MCU AVR 16K FLASH 15MHZ 20-TSSOP
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY167-15XD

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, LIN, SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 16
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 150°C
• Package / Case: 20-TSSOP
• Processor Series: ATTINY1x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Maximum Clock Frequency: 16 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• For Use With: ATSTK600-SOIC - STK600 SOCKET/ADAPTER FOR SOIC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

15.3.3
15.3.4
15.3.5
15.4
164
LIN / UART Controller
ATtiny87/ATtiny167
Data Transport
Schedule Table
Compatibility with LIN 1.3
Two types of data may be transported in a frame; signals or diagnostic messages.
The master task (in the master node) transmits frame headers based on a schedule table. The
schedule table specifies the identifiers for each header and the interval between the start of a
frame and the start of the following frame. The master application may use different schedule
tables and select among them.
LIN 2.1 is a super-set of LIN 1.3.
A LIN 2.1 master node can handle clusters consisting of both LIN 1.3 slaves and/or LIN 2.1
slaves. The master will then avoid requesting the new LIN 2.1 features from a LIN 1.3 slave:
LIN 2.1 slave nodes can not operate with a LIN 1.3 master node (e.g. the LIN1.3 master does
not support the enhanced checksum).
The LIN 2.1 physical layer is backwards compatible with the LIN1.3 physical layer. But not the
other way around. The LIN 2.1 physical layer sets greater requirements, i.e. a master node
using the LIN 2.1 physical layer can operate in a LIN 1.3 cluster.
The LIN/UART controller is divided in three main functions:
These functions mainly use two services:
Because these two services are basically UART services, the controller is also able to switch
into an UART function.
• Signals
• Diagnostic messages
• Enhanced checksum,
• Re-configuration and diagnostics,
• Automatic baud rate detection,
• "Response error" status monitoring.
• Tx LIN Header function,
• Rx LIN Header function,
• LIN Response function.
• Rx service,
• Tx service.
Signals are scalar values or byte arrays that are packed into the data field of a frame. A
signal is always present at the same position in the data field for all frames with the same
identifier.
Diagnostic messages are transported in frames with two reserved identifiers. The
interpretation of the data field depends on the data field itself as well as the state of the
communicating nodes.
7728G–AVR–06/10