M306N5FCTFP Renesas Electronics America, M306N5FCTFP Datasheet - Page 221

• Manufacturer Part Number: M306N5FCTFP
• Description: IC M16C MCU FLASH 100QFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/6Nr

Specifications of M306N5FCTFP

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: CAN, I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 87
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 5K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 26x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

M16C/6N Group (M16C/6N5)
Rev.2.40
REJ09B0011-0240
Figure 16.7 Registers ADCON0 and ADCON1 in Repeat Sweep Mode 0
A/D Control Register 0
NOTE:
A/D Control Register 1
NOTES:
b7
b7
1. If the ADCON0 register is rewritten during A/D conversion, the conversion result will be undefined.
1. If the ADCON1 register is rewritten during A/D conversion, the conversion result will be undefined.
2. AN0_0 to AN0_7, and AN2_0 to AN2_7 can be used in same way as AN0 to AN7. Use bits ADGSEL1 to
3. If the VCUT bit is reset from 0 (VREF unconnected) to 1 (VREF connected), wait for 1 µs or more before
Apr 14, 2006
b6
b6
ADGSEL0 in the ADCON2 register to select the desired pin.
starting A/D conversion.
1
b5
b5
1
b4
b4
1
b3
b3
0
b2
b2
page 199 of 372
b1
b1
b0
b0
Bit Symbol
Bit Symbol
(1)
(1)
SCAN0
SCAN1
ADST
VCUT
OPA0
OPA1
CKS0
CKS1
MD0
MD1
TRG
MD2
BITS
CH0
CH1
CH2
ADCON0
ADCON1
Symbol
Symbol
Analog input pin select bits
A/D operating mode
select bits 0
Trigger select bit
A/D conversion start flag
Frequency select bit 0
A/D sweep pin select bits
A/D operating mode
select bit 1
8/10-bit mode select bit
Frequency select bit 1
VREF connect bit
External op-amp
connection mode bits
Address
Address
Bit Name
Bit Name
03D6h
03D7h
(3)
After Reset
00000XXXb
After reset
Invalid in repeat sweep mode 0
b4 b3
1 1 : Repeat sweep mode 0 or
0 : Software trigger
1 : ADTRG trigger
0 : A/D conversion disabled
1 : A/D conversion started
Refer to NOTE 2 for ADCON2
Register
When repeat sweep mode 0 is selected
b1 b0
0 0 : AN0, AN1 (2 pins)
0 1 : AN0 to AN3 (4 pins)
1 0 : AN0 to AN5 (6 pins)
1 1 : AN0 to AN7 (8 pins)
Set to 0 when repeat sweep
mode 0 is selected
0 : 8-bit mode
1 : 10-bit mode
Refer to NOTE 2 for ADCON2
Register
1 : VREF connected
b7 b6
0 0 : ANEX0 and ANEX1 are not used
0 1 : Do not set a value
1 0 : Do not set a value
1 1 : External op-amp connection mode
00h
Repeat sweep mode 1
Function
Function
(2)
16. A/D Converter
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW
RW