M306N5FCTFP Renesas Electronics America, M306N5FCTFP Datasheet - Page 84

• Manufacturer Part Number: M306N5FCTFP
• Description: IC M16C MCU FLASH 100QFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/6Nr

Specifications of M306N5FCTFP

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: CAN, I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 87
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 5K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 26x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

M16C/6N Group (M16C/6N5)
Rev.2.40
REJ09B0011-0240
Table 8.6 Interrupts to Stop Mode and Use Conditions
Table 8.7 Pin Status in Stop Mode
___________
______ _______ _________ _________
A0 to A19, D0 to D15,
_______
CS0 to CS3, BHE
RD, WR, WRL, WRH
HLDA, BCLK
ALE
I/O ports
CLKOUT
_______
NMI interrupt
Key input interrupt
______
INT interrupt
Timer A interrupt
Timer B interrupt
Serial interface interrupt
CAN0 wake-up interrupt
8.4.3 Stop Mode
In stop mode, all oscillator circuits are turned off, so are the CPU clock and the peripheral function clocks.
Therefore, the CPU and the peripheral functions clocked by these clocks stop operating. The least
amount of power is consumed in this mode. If the voltage applied to VCC pin is VRAM or more, the
internal RAM is retained.
However, the peripheral functions clocked by external signals keep operating.
Table 8.6 lists the Interrupts to Stop Mode and Use Conditions.
8.4.3.1 Entering Stop Mode
8.4.3.2 Pin Status in Stop Mode
The MCU is placed into stop mode by setting the CM10 bit in the CM1 register to 1 (all clocks turned off).
At the same time, the CM06 bit in the CM0 register is set to 1 (divide-by-8 mode) and the CM15 bit in the
CM1 register is set to 1 (main clock oscillator circuit drive capability high).
Before entering stop mode, set the CM20 bit in the CM2 register to 0 (oscillation stop, re-oscillation
detection function disabled).
Also, if the CM11 bit in the CM1 register is 1 (PLL clock for the CPU clock source), set the CM11 bit to 0
(main clock for the CPU clock source) and the PLC07 bit in the PLC0 register to 0 (PLL turned off) before
entering stop mode.
Table 8.7 lists the Pin Status in Stop Mode.
Apr 14, 2006
_______
When fC selected
When f8, f32
selected
Interrupt
Pin
________
page 62 of 372
Retains status before stop mode
“H”
“H”
undefined
Retains status before stop mode
Does not become a CLKOUT pin
Can be used
Can be used
Can be used
Can be used
(when counting external pulses in event counter mode)
Can be used (when external clock is selected)
Can be used (when CAN sleep mode is selected)
Memory Expansion Mode
Microprocessor Mode
Condition
Does not become a bus control pin
Retains status before stop mode
“H”
Retains status before stop mode
Single-chip Mode
8. Clock Generation Circuit