M306N5FCTFP Renesas Electronics America, M306N5FCTFP Datasheet - Page 53

• Manufacturer Part Number: M306N5FCTFP
• Description: IC M16C MCU FLASH 100QFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/6Nr

Specifications of M306N5FCTFP

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: CAN, I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 87
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 5K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 26x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

M16C/6N Group (M16C/6N5)
Rev.2.40
REJ09B0011-0240
Figure 6.1 PM0 Register
Processor Mode Register 0
NOTES:
b7
1. Rewrite this register after setting the PRC1 bit in the PRCR register to 1 (write enabled).
2. Bits PM01 to PM00 do not change at software reset, watchdog timer reset and oscillation stop detection reset.
3. Effective when bits PM01 to PM00 are set to 01b (memory expansion mode) or 11b (microprocessor mode).
4. To set bits PM01 to PM00 are 01b and bits PM05 to PM04 are 11b (multiplexed bus assigned to the entire
Apr 14, 2006
b6
CS space), apply an "H" signal to the BYTE pin (external data bus is 8-bit width).
While the CNVSS pin is held "H" (VCC), do not rewrite bits PM05 to PM04 to 11b after reset.
If bits PM05 to PM04 are set to 11b during memory expansion mode, P3_1 to P3_7 and P4_0 to P4_3 become
I/O ports, in which case the accessible area for each CS is 256 bytes.
b5
b4
b3
b2
page 31 of 372
b1
b0
Bit Symbol
PM00
PM01
PM02
PM03
PM04
PM05
PM06
PM07
Symbol
PM0
(1)
Processor mode bits
R/W Mode select bit
Software reset bit
Multiplexed bus space
select bits
Port P4_0 to P4_3 function
select bit
BCLK output disable
bit
(3)
Address
Bit Name
0004h
(3)
(3)
(3)
(2)
00000000b (CNVSS pin = L)
00000011b (CNVSS pin = H)
0 0 : Single-chip mode
0 1 : Memory expansion mode
1 0 : Do not set a value
1 1 : Microprocessor mode
0 : RD, BHE, WR
1 : RD, WRH, WRL
Setting this bit to 1 resets the
MCU.
When read, the content is 0.
b5 b4
0 0 : Multiplexed bus is unused
0 1 : Allocated to CS2 space
1 0 : Allocated to CS1 space
1 1 : Allocated to the entire CS space
0 : Address output
1 : Port function
0 : BCLK is output
1 : BCLK is not output
b1 b0
(Address is not output)
(Pin is left high-impedance)
(Separate bus in the entire CS space)
After Reset
Function
(2)
6. Processor Mode
(4)
RW
RW
RW
RW
RW
RW
RW
RW
RW