XR17V258IV-F Exar Corporation, XR17V258IV-F Datasheet - Page 25

• Manufacturer Part Number: XR17V258IV-F
• Description: IC UART PCI BUS OCTAL 144LQFP
• Manufacturer: Exar Corporation
• Type: Octal UARTr

Specifications of XR17V258IV-F

• Number Of Channels: 8
• Package / Case: 144-LQFP
• Features: *
• Fifo's: 64 Byte
• Protocol: RS485
• Voltage - Supply: 3.3V, 5V
• With Auto Flow Control: Yes
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• Mounting Type: Surface Mount
• Data Rate: 8 Mbps
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 3 V
• Supply Current: 4 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 45 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 3 V to 3.6 V
• No. Of Channels: 8
• Uart Features: Tx/Rx FIFO Counters
• Supply Voltage Range: 3V To 3.6V
• Operating Temperature Range: -40°C To +85°C
• Digital Ic Case Style: LQFP
• No. Of Pins: 144
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

REV. 1.0.2
The V258 provides 8 multi-purpose inputs/outputs MPIO[7:0] for general use. Each pin can be programmed to
be an input or output function. The input logic state can be set for normal or inverted level, and optionally set to
generate an interrupt. The outputs can be set to be normal HIGH or LOW state, or 3-state. Their functions and
definitions are programmed through 5 registers: MPIOINT, MPIOLVL, MPIO3T, MPIOINV and MPIOSEL. If all
8 pins are set for inputs, all 8 interrupts would be ORed together. The ORed interrupt is reported in the channel
0 UART interrupt status, see Interrupt Status Register. The pins may also be programmed to be outputs and to
the 3-state condition for signal sharing. The MPIO[0] pin can be programmed to show the Timer output. When
it is programmed to be the Timer output, all the above 5 registers lose control over the MPIO[0] pin. For details
on Timer output, please see
TIMELSB, TIMER, TIMECNTL] (default 0xXX-XX-00-00)” on page 20
There are 5 registers that select, control and monitor the 8 multipurpose inputs and outputs.
the internal circuitry.
REGB[16](Read/Write)
REGB[19:17]
REGB[20] (Write-Only)
REGB[21] (Write-Only)
REGB[22] (Write-Only)
REGB[23] (Read-Only)
1.6.8
1.6.9
1.6.10
REGB Register
Multi-Purpose Inputs and Outputs
MPIO REGISTERS
Logic 0 (default) write to each UART configuration registers individually.
Logic 1 enables simultaneous write to all 8 UARTs configuration register.
Reserved
Control the EECK, clock, output (pin 116) on the EEPROM interface.
Control the EECS, chips select, output (pin 115) to the EEPROM device.
EEDI (pin 114) data input. Write data to the EEPROM device.
EEDO (pin 113) data output. Read data from the EEPROM device.
66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
“Section 1.6.2, General Purpose 16-bit Timer/Counter [TIMERMSB,
25
.
Figure 9
XR17V258
shows