XR17V258IV-F Exar Corporation, XR17V258IV-F Datasheet - Page 46

• Manufacturer Part Number: XR17V258IV-F
• Description: IC UART PCI BUS OCTAL 144LQFP
• Manufacturer: Exar Corporation
• Type: Octal UARTr

Specifications of XR17V258IV-F

• Number Of Channels: 8
• Package / Case: 144-LQFP
• Features: *
• Fifo's: 64 Byte
• Protocol: RS485
• Voltage - Supply: 3.3V, 5V
• With Auto Flow Control: Yes
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• Mounting Type: Surface Mount
• Data Rate: 8 Mbps
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 3 V
• Supply Current: 4 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 45 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 3 V to 3.6 V
• No. Of Channels: 8
• Uart Features: Tx/Rx FIFO Counters
• Supply Voltage Range: 3V To 3.6V
• Operating Temperature Range: -40°C To +85°C
• Digital Ic Case Style: LQFP
• No. Of Pins: 144
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

XR17V258
66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
]
ISR[7:6]: FIFO Enable Status
These bits are set to a logic 0 when the FIFOs are disabled. They are set to a logic 1 when the FIFOs are
enabled.
ISR[5:1]: Interrupt Status
These bits indicate the source for a pending interrupt at interrupt priority levels (See
5.5.1, Interrupt Generation:” on page 46
5.5.1
5.5.2
P
LSR is by any of the LSR bits [4:1]. See IER bit [2] description on the previous page.
RXRDY is by RX trigger level.
RXRDY Time-out is by a 4-char plus 12 bits delay timer.
TXRDY is by TX trigger level or TX FIFO empty (or transmitter empty in auto RS-485 control).
MSR is by any of the MSR bits [3:0].
Receive Xon/Xoff/Special character is by detection of a Xon, Xoff or Special character.
CTS#/DSR# is when its transmitter toggles the input pin (from LOW to HIGH) during auto CTS/DSR flow
control enabled by EFR bit [7] and selection on MCR bit [2].
RTS#/DTR# is when its receiver toggles the output pin (from LOW to HIGH) during auto RTS/DTR flow
control enabled by EFR bit [6] and selection on MCR bit [2].
Wake-up indicator is when the UART wakes up from the sleep mode.
LSR interrupt is cleared by a read to the LSR register.
RXRDY interrupt is cleared by reading data until FIFO falls below the trigger level.
RXRDY Time-out interrupt is cleared by reading RHR.
TXRDY interrupt is cleared by a read to the ISR register or writing to THR.
MSR interrupt is cleared by a read to the MSR register.
Xon or Xoff interrupt is cleared by a read to ISR register.
Special character interrupt is cleared by a read to ISR or after the next character is received.
RTS#/DTR# and CTS#/DSR# status change interrupts are cleared by a read to the MSR register.
Wake-up indicator is cleared by a read to the INT0 register.
RIORITY
L
EVEL
X
1
2
3
4
5
6
7
Interrupt Generation:
Interrupt Clearing:
B
IT
0
0
0
0
0
0
1
0
[5]
B
IT
0
0
0
0
0
1
0
0
[4]
ISR R
B
IT
T
EGISTER
0
0
1
0
0
0
0
0
ABLE
[3]
16: I
B
S
IT
TATUS
1
1
1
0
0
0
0
0
[2]
NTERRUPT
and
B
B
ITS
IT
“Section 5.5.2, Interrupt Clearing:” on page 46
1
0
0
1
0
0
0
0
[1]
S
OURCE AND
46
B
IT
0
0
0
0
0
0
0
1
[0]
LSR (Receiver Line Status Register)
RXRDY (Received Data Ready)
RXRDY (Receive Data Time-out)
TXRDY (Transmitter Holding Register Empty)
MSR (Modem Status Register)
RXRDY (Received Xon/Xoff or Special character)
CTS#/DSR#, RTS#/DTR# change of state
None (default)
P
RIORITY
L
S
EVEL
OURCE OF THE INTERRUPT
Table 16
). See
for details.
REV. 1.0.2
“Section