ATTINY461-20PU Atmel, ATTINY461-20PU Datasheet - Page 121

• Manufacturer Part Number: ATTINY461-20PU
• Description: Microcontrollers (MCU) 4kB Flash 0.256kB EEPROM 16 I/O Pins
• Manufacturer: Atmel

Specifications of ATTINY461-20PU

• Processor Series: ATTINY4x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: 2-Wire/SPI/USI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 2
• Operating Supply Voltage: 4.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 11-ch x 10-bit
• Program Memory Type: Flash
• Program Memory Size: 4 KB
• Package / Case: PDIP-20
• Package: 20PDIP
• Device Core: AVR
• Family Name: ATtiny
• Maximum Speed: 20 MHz
• Ram Size: 256 Byte
• Operating Temperature: -40 to 85 °C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

12.12.7
12.12.8
12.12.9
2588E–AVR–08/10
TCNT1 – Timer/Counter1
TC1H – Timer/Counter1 High Byte
OCR1A – Timer/Counter1 Output Compare Register A
This 8-bit register contains the value of Timer/Counter1.
The Timer/Counter1 is realized as a 10-bit up/down counter with read and write access. Due to
synchronization of the CPU, Timer/Counter1 data written into Timer/Counter1 is delayed by one
and half CPU clock cycles in synchronous mode and at most one CPU clock cycles for asyn-
chronous mode. When a 10-bit accuracy is preferred, special procedures must be followed for
accessing the 10-bit TCNT1 register via the 8-bit AVR data bus. These procedures are
described in section
can be used as an 8-bit Timer/Counter. Note that the Timer/Counter1 always starts counting up
after writing the TCNT1 register.
The temporary Timer/Counter1 register is an 2-bit read/write register.
• Bits 7:2 – Res: Reserved Bits
These bits are reserved and always reads zero.
• Bits 1:0 – TC19, TC18: Two MSB bits of the 10-bit accesses
If 10-bit accuracy is used, the Timer/Counter1 High Byte Register (TC1H) is used for temporary
storing the MSB bits (TC19, TC18) of the 10-bit acceses. The same TC1H register is shared
between all 10-bit registers within the Timer/Counter1. Note that special procedures must be fol-
lowed when accessing the 10-bit TCNT1 register via the 8-bit AVR data bus. These procedures
are described in section
The output compare register A is an 8-bit read/write register.
The Timer/Counter Output Compare Register A contains data to be continuously compared with
Timer/Counter1. Actions on compare matches are specified in TCCR1A. A compare match does
only occur if Timer/Counter1 counts to the OCR1A value. A software write that sets TCNT1 and
OCR1A to the same value does not generate a compare match.
A compare match will set the compare interrupt flag OCF1A after a synchronization delay follow-
ing the compare event.
Note that, if 10-bit accuracy is used special procedures must be followed when accessing the
internal 10-bit Ouput Compare Registers via the 8-bit AVR data bus. These procedures are
described in section
Bit
0x2E (0x4E)
Read/Write
Initial value
Bit
0x25 (0x45)
Read/Write
Initial value
Bit
0x2D (0x4D)
Read/Write
Initial value
MSB
MSB
R/W
R/W
R
7
0
7
0
7
0
-
“Accessing 10-Bit Registers” on page
“Accessing 10-Bit Registers” on page
“Accessing 10-Bit Registers” on page
R/W
R/W
R
6
0
6
0
6
0
-
R/W
R/W
R
5
0
5
0
5
0
-
R/W
R/W
R
4
0
4
0
4
0
-
R/W
R/W
R
3
0
3
0
3
0
-
108. Alternatively the Timer/Counter1
108.
R/W
R/W
108.
R
2
0
2
0
2
0
-
TC19
R/W
R/W
R/W
1
0
1
0
1
0
TC18
LSB
LSB
R/W
R/W
R/W
0
0
0
0
0
0
OCR1A
TCNT1
TC1H
121