ATTINY461-20PU Atmel, ATTINY461-20PU Datasheet - Page 122

• Manufacturer Part Number: ATTINY461-20PU
• Description: Microcontrollers (MCU) 4kB Flash 0.256kB EEPROM 16 I/O Pins
• Manufacturer: Atmel

Specifications of ATTINY461-20PU

• Processor Series: ATTINY4x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: 2-Wire/SPI/USI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 2
• Operating Supply Voltage: 4.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 11-ch x 10-bit
• Program Memory Type: Flash
• Program Memory Size: 4 KB
• Package / Case: PDIP-20
• Package: 20PDIP
• Device Core: AVR
• Family Name: ATtiny
• Maximum Speed: 20 MHz
• Ram Size: 256 Byte
• Operating Temperature: -40 to 85 °C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

12.12.10 OCR1B – Timer/Counter1 Output Compare Register B
12.12.11 OCR1C – Timer/Counter1 Output Compare Register C
12.12.12 OCR1D – Timer/Counter1 Output Compare Register D
122
ATtiny261/461/861
The output compare register B is an 8-bit read/write register.
The Timer/Counter Output Compare Register B contains data to be continuously compared with
Timer/Counter1. Actions on compare matches are specified in TCCR1. A compare match does
only occur if Timer/Counter1 counts to the OCR1B value. A software write that sets TCNT1 and
OCR1B to the same value does not generate a compare match.
A compare match will set the compare interrupt flag OCF1B after a synchronization delay follow-
ing the compare event.
Note that, if 10-bit accuracy is used special procedures must be followed when accessing the
internal 10-bit Output Compare Registers via the 8-bit AVR data bus. These procedures are
described in section
The output compare register C is an 8-bit read/write register.
The Timer/Counter Output Compare Register C contains data to be continuously compared with
Timer/Counter1, and a compare match will clear TCNT1. This register has the same function in
Normal mode and PWM modes.
Note that, if a smaller value than three is written to the Output Compare Register C, the value is
automatically replaced by three as it is a minumum value allowed to be written to this register.
Note that, if 10-bit accuracy is used special procedures must be followed when accessing the
internal 10-bit Output Compare Registers via the 8-bit AVR data bus. These procedures are
described in section
The output compare register D is an 8-bit read/write register.
The Timer/Counter Output Compare Register D contains data to be continuously compared with
Timer/Counter1. Actions on compare matches are specified in TCCR1A. A compare match does
only occur if Timer/Counter1 counts to the OCR1D value. A software write that sets TCNT1 and
OCR1D to the same value does not generate a compare match.
A compare match will set the compare interrupt flag OCF1D after a synchronization delay follow-
ing the compare event.
Bit
0x2C (0x4C)
Read/Write
Initial value
Bit
0x2B (0x4B)
Read/Write
Initial value
Bit
0x2A (0x4A)
Read/Write
Initial value
MSB
MSB
MSB
R/W
R/W
R/W
7
0
7
1
7
0
“Accessing 10-Bit Registers” on page
“Accessing 10-Bit Registers” on page
R/W
R/W
R/W
6
0
6
1
6
0
R/W
R/W
R/W
5
0
5
1
5
0
R/W
R/W
R/W
4
0
4
1
4
0
R/W
R/W
R/W
3
0
3
1
3
0
108.
108.
R/W
R/W
R/W
2
0
2
1
2
0
R/W
R/W
R/W
1
0
1
1
1
0
LSB
R/W
LSB
R/W
LSB
R/W
0
0
0
1
0
0
2588E–AVR–08/10
OCR1D
OCR1B
OCR1C