PIC18F64J11T-I/PT Microchip Technology, PIC18F64J11T-I/PT Datasheet - Page 134

• Manufacturer Part Number: PIC18F64J11T-I/PT
• Description: 16KB, Flash, 1024bytes-RAM, 51I/O, 8-bit Family,nanoWatt 64 TQFP 10x10x1mm T/R
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F64J11T-I/PT

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 51
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA180018 - MODULE PLUG-IN 18F85J11AC162079 - HEADER MPLAB ICD2 18F85J90 64/80AC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: PIC18F64J11T-I/PTTR

PIC18F85J11 FAMILY
11.4
PORTC is an 8-bit wide, bidirectional port. The corre-
sponding Data Direction and Output Latch registers are
TRISC and LATC. Only PORTC pins, RC2 through
RC7, are digital only pins and can tolerate input
voltages up to 5.5V.
PORTC is multiplexed with CCP, MSSP and EUSART
peripheral functions (Table 11-7). The pins have
Schmitt Trigger input buffers. The pins for CCP, SPI
and EUSART are also configurable for open-drain out-
put whenever these functions are active. Open-drain
configuration is selected by setting the SPIOD,
CCPxOD and U1OD control bits (TRISG<7:5> and
LATG<6>, respectively).
RC1 is normally configured as the default peripheral
pin for the CCP2 module. Assignment of CCP2 is
controlled by Configuration bit, CCP2MX (default state,
CCP2MX = 1).
DS39774D-page 134
PORTC, TRISC and
LATC Registers
When enabling peripheral functions, care should be
taken in defining TRIS bits for each PORTC pin. Some
peripherals override the TRIS bit to make a pin an output,
while other peripherals override the TRIS bit to make a
pin an input. The user should refer to the corresponding
peripheral section for the correct TRIS bit settings.
The contents of the TRISC register are affected by
peripheral overrides. Reading TRISC always returns
the current contents, even though a peripheral device
may be overriding one or more of the pins.
EXAMPLE 11-3:
CLRF
CLRF
MOVLW
MOVWF
Note:
PORTC
LATC
0CFh
TRISC
These pins are configured as digital inputs
on any device Reset.
; Initialize PORTC by
; clearing output
; data latches
; Alternate method
; to clear output
; data latches
; Value used to
; initialize data
; direction
; Set RC<3:0> as inputs
; RC<5:4> as outputs
; RC<7:6> as inputs
INITIALIZING PORTC
 2010 Microchip Technology Inc.