KSZ8842-16MQL Micrel Inc, KSZ8842-16MQL Datasheet - Page 24

• Manufacturer Part Number: KSZ8842-16MQL
• Description: IC SWITCH 10/100 16BIT 128PQFP
• Manufacturer: Micrel Inc

Specifications of KSZ8842-16MQL

• Data Rate: 100Mbps
• Controller Type: Ethernet Switch Controller
• Interface: PCI
• Voltage - Supply: 3.1 V ~ 3.5 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 128-MQFP, 128-PQFP
• No. Of Ports: 1
• Ethernet Type: IEEE 802.3u
• Supply Current: 122mA
• Supply Voltage Range: 3.1V To 3.5V
• Operating Temperature Range: 0°C To +70°C
• Digital Ic Case Style: QFP
• No. Of: RoHS Compliant
• Number Of Primary Switch Ports: 2
• Internal Memory Buffer Size: 32
• Operating Supply Voltage (typ): 3.3V
• Fiber Support: Yes
• Integrated Led Drivers: Yes
• Phy/transceiver Interface: MII
• Power Supply Type: Analog/Digital
• Package Type: PQFP
• Data Rate (typ): 10/100Mbps
• Vlan Support: Yes
• Operating Temperature (max): 70C
• Operating Temperature (min): 0C
• Pin Count: 128
• Mounting: Surface Mount
• Jtag Support: No
• Operating Supply Voltage (max): 3.5V
• Operating Supply Voltage (min): 3.1V
• Operating Temperature Classification: Commercial
• Interface Type: PCI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 576-1634 - BOARD EVALUATION KSZ8842-16MQL
• Current - Supply: -
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant
• Other names: 576-1478-5

Crossover Cable
A crossover cable connects an MDI device to another MDI device, or an MDI-X device to another MDI-X device. The
following diagram shows a typical crossover cable connection between two switches or hubs (two MDI-X devices).
Auto Negotiation
The KSZ8842M conforms to the auto negotiation protocol as described by the 802.3 committee to allow the channel to
operate at 10Base-T or 100Base-TX.
Auto negotiation allows unshielded twisted pair (UTP) link partners to select the best common mode of operation. In auto
negotiation, the link partners advertise capabilities across the link to each other. If auto negotiation is not supported or the
link partner to the KSZ8842M is forced to bypass auto negotiation, the mode is set by observing the signal at the receiver.
This is known as parallel mode because while the transmitter is sending auto negotiation advertisements, the receiver is
listening for advertisements or a fixed signal protocol.
The link setup is shown in the following flow diagram (Figure 8).
Micrel Confidential
November 2005
M e d i a D e p e n d e n t I n terface
M o d u l a r C o n n e ct o r (RJ-45)
T r a n sm i t P a i r
R e ce i v e P a i r
( R e p e a t e r o r S w i tch)
1 0 / 1 0 0 E t h e r n et
Figure 7. Typical Crossover Cable Connection
H U B
1
2
3
4
5
6
7
8
Crossover
Cable
24
Media Dependent Interface
Modular Connector (RJ-45)
(Repeater or Switch)
1
2
3
4
5
6
7
8
10/100 Ethernet
Transmit Pair
HUB
Receive Pair
KSZ8842-16/32 MQL/MVL
Rev. 1.4