KSZ8842-16MQL Micrel Inc, KSZ8842-16MQL Datasheet - Page 31

• Manufacturer Part Number: KSZ8842-16MQL
• Description: IC SWITCH 10/100 16BIT 128PQFP
• Manufacturer: Micrel Inc

Specifications of KSZ8842-16MQL

• Data Rate: 100Mbps
• Controller Type: Ethernet Switch Controller
• Interface: PCI
• Voltage - Supply: 3.1 V ~ 3.5 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 128-MQFP, 128-PQFP
• No. Of Ports: 1
• Ethernet Type: IEEE 802.3u
• Supply Current: 122mA
• Supply Voltage Range: 3.1V To 3.5V
• Operating Temperature Range: 0°C To +70°C
• Digital Ic Case Style: QFP
• No. Of: RoHS Compliant
• Number Of Primary Switch Ports: 2
• Internal Memory Buffer Size: 32
• Operating Supply Voltage (typ): 3.3V
• Fiber Support: Yes
• Integrated Led Drivers: Yes
• Phy/transceiver Interface: MII
• Power Supply Type: Analog/Digital
• Package Type: PQFP
• Data Rate (typ): 10/100Mbps
• Vlan Support: Yes
• Operating Temperature (max): 70C
• Operating Temperature (min): 0C
• Pin Count: 128
• Mounting: Surface Mount
• Jtag Support: No
• Operating Supply Voltage (max): 3.5V
• Operating Supply Voltage (min): 3.1V
• Operating Temperature Classification: Commercial
• Interface Type: PCI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 576-1634 - BOARD EVALUATION KSZ8842-16MQL
• Current - Supply: -
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant
• Other names: 576-1478-5

Given a physical data bus size, the KSZ8842M supports 8, 16, or 32-bit data transfers depending on the size of the
physical data bus. For example, for a 32-bit system/host data bus, it allows 8, 16, and 32-bit data transfers (KSZ8842-
32MQL); for a 16-bit system/host data bus, it allows 8 and 16-bit data transfers (KSZ8842-16MQL); and for 8-bit
system/host data bus, it only allows 8-bit data transfers (KSZ8842-16MQL).
Note that KSZ8842M does not support internal data byte-swap but it does support internal data word-swap. This means
that the system/host data bus HD[7:0] has to connect to both D[7:0] and D[15:8] for 8-bit data bus interfaces. However,
the system/host data bus HD[15:8] and HD[7:0] just connects to D[15:8] and D[7:0], respectively, for 16-bit data bus
interface; there is no need to connect HD[31:24] and HD[23:16] to D[31:24] and D[23:16].
Table 2 describes the BIU signal grouping.
Micrel Confidential
November 2005
Signal
Common Signals
A[15:1]
AEN
BE3N, BE2N,
BE1N, BE0N
D[31:16]
D[15:0]
ADSN
LDEVN
DATACSN
INTRN
Synchronous Transfer Signals
VLBUSN
Type
I
I
I
I/O
I/O
I
O
I
O
I
(1)
Function
Address
Address Enable
Address Enable asserted indicates memory address on the bus for DMA
access and since the device is an I/O device, address decoding is only enabled
when AEN is low.
Byte Enable
Note 1: BE3N, BE2N, BE1N and BE0N are ignored when DATACSN is low
because 32 bit transfers are assumed.
Note 2: BE2N and BE3N are valid only for the KSZ8842-32 mode, and are NC
for the KSZ8842-16 mode.
Data
For KSZ8842-32 Mode only
Data
For both KSZ8842-32 and KSZ8842-16 Modes
Address Strobe
The rising edge of ADSN is used to latch A[15:1], AEN, BE3N, BE2N, BE1N
and BE0N.
Local Device
This signal is a combinatorial decode of AEN and A[15:4], The A[15:4] is used
to compare against the Base Address Register.
Data Register Chip Select (For KSZ8842-32 Mode only)
This signal is used for central decoding architecture (mostly for embedded
application). When asserted, the device’s local decoding logic is ignored and
the 32-bit access to QMU Data Register is assumed.
Interrupt
VLBUSN = 0, VLBus-like cycle.
BE0N
0
0
1
0
1
1
1
BE1N
0
0
1
1
0
1
1
31
BE2N
0
1
0
1
1
0
1
BE3N
0
1
0
1
1
1
0
Description
32-bit access (32-bit bus only)
Lower 16-bit (D[15:0]) access
Higher 16-bit (D[31:16]) access
(32-bit bus only)
Byte 0 (D[7:0]) access
Byte 1 (D[15:8]) access
Byte 2 (D[23:16]) access (32-bit
bus only)
Byte 3 (D[31:24]) access (32-bit
bus only)
KSZ8842-16/32 MQL/MVL
Rev. 1.4