KSZ8842-16MQL Micrel Inc, KSZ8842-16MQL Datasheet - Page 35

• Manufacturer Part Number: KSZ8842-16MQL
• Description: IC SWITCH 10/100 16BIT 128PQFP
• Manufacturer: Micrel Inc

Specifications of KSZ8842-16MQL

• Data Rate: 100Mbps
• Controller Type: Ethernet Switch Controller
• Interface: PCI
• Voltage - Supply: 3.1 V ~ 3.5 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 128-MQFP, 128-PQFP
• No. Of Ports: 1
• Ethernet Type: IEEE 802.3u
• Supply Current: 122mA
• Supply Voltage Range: 3.1V To 3.5V
• Operating Temperature Range: 0°C To +70°C
• Digital Ic Case Style: QFP
• No. Of: RoHS Compliant
• Number Of Primary Switch Ports: 2
• Internal Memory Buffer Size: 32
• Operating Supply Voltage (typ): 3.3V
• Fiber Support: Yes
• Integrated Led Drivers: Yes
• Phy/transceiver Interface: MII
• Power Supply Type: Analog/Digital
• Package Type: PQFP
• Data Rate (typ): 10/100Mbps
• Vlan Support: Yes
• Operating Temperature (max): 70C
• Operating Temperature (min): 0C
• Pin Count: 128
• Mounting: Surface Mount
• Jtag Support: No
• Operating Supply Voltage (max): 3.5V
• Operating Supply Voltage (min): 3.1V
• Operating Temperature Classification: Commercial
• Interface Type: PCI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 576-1634 - BOARD EVALUATION KSZ8842-16MQL
• Current - Supply: -
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant
• Other names: 576-1478-5

Queue Management Unit (QMU)
The Queue Management Unit (QMU) manages packet traffic between the MAC/PHY interface and the system host. It has
built-in packet memory for receive and transmit functions called TXQ (Transmit Queue) and RXQ (Receive Queue). Each
queue contains 4KB of memory for back-to-back, non-blocking frame transfer performance. It provides a group of control
registers for system control, frame status registers for current packet transmit/receive status, and interrupts to inform the
host of the real time TX/RX status.
Transmit Queue (TXQ) Frame Format
The frame format for the transmit queue is shown in the following Table 3. The first word contains the control information
for the frame to transmit. The second word is used to specify the total number of bytes of the frame. The packet data
follows. The packet data area holds the frame itself. It may or may not include the CRC checksum depending on whether
hardware CRC checksum generation is enabled.
Multiple frames can be pipelined in both the transmit queue and receive queue as long as there is enough queue memory,
thus avoiding overrun. For each transmitted frame, the transmit status information for the frame is located in the TXSR
register.
Micrel Confidential
November 2005
2. Internal byte swapping is not implemented and word swapping is supported internally. Refer to Figure 12 for the
3. Since independent sets of synchronous and asynchronous signals are provided, synchronous and asynchronous
4. The asynchronous interface uses RDN and WRN signal strobes for data latching. If necessary, ARDY is de-
5. The VLBUS-like synchronous interface uses BCLK, ADSN, and SWR and CYCLEN to control read and write
6. The EISA-like burst transfer is supported using synchronous interface signals and DATACSN when I/O signal
Since multiple packets can be pipelined into the TX packet memory for transmit, the transmit status reflects the
status of the packet that is currently being transferred on the MAC interface (which may or may not be the last
queued packet in the TX queue).
The transmit control word is the first 16-bit word in the TX packet memory, followed by a 16-bit byte count.
be word aligned.
fields.
appropriate 8-bit, 16-bit, and 32-bit data bus connection.
cycles can be mixed or interleaved as long as they are not active simultaneously.
asserted on the leading edge of the strobe.
operations and generate SRDYN to insert the wait state, if necessary, when VLBUSN = 0. For read, the data must
be held until RDYRTNN is asserted.
VLBUSN = 1. Both the system/host/memory and KSZ8842M are capable of inserting wait states. To set the
system/host/memory to insert a wait state, assert RDYRTNN signal. To set the KSZ8842M to insert a wait state,
assert SRDYN signal.
Each control word corresponds to one TX packet. Table 4 gives the transmit control word bit
Packet Memory
Address Offset
0
2
4 - up
Table 3: Transmit Queue Frame Format
Bit 15
2
Control Word
Byte Count
Packet Data
(maximum size is 1916)
nd
Byte
35
1
st
Bit 0
Byte
KSZ8842-16/32 MQL/MVL
Rev. 1.4
It must