KSZ8842-16MQL Micrel Inc, KSZ8842-16MQL Datasheet - Page 55

• Manufacturer Part Number: KSZ8842-16MQL
• Description: IC SWITCH 10/100 16BIT 128PQFP
• Manufacturer: Micrel Inc

Specifications of KSZ8842-16MQL

• Data Rate: 100Mbps
• Controller Type: Ethernet Switch Controller
• Interface: PCI
• Voltage - Supply: 3.1 V ~ 3.5 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 128-MQFP, 128-PQFP
• No. Of Ports: 1
• Ethernet Type: IEEE 802.3u
• Supply Current: 122mA
• Supply Voltage Range: 3.1V To 3.5V
• Operating Temperature Range: 0°C To +70°C
• Digital Ic Case Style: QFP
• No. Of: RoHS Compliant
• Number Of Primary Switch Ports: 2
• Internal Memory Buffer Size: 32
• Operating Supply Voltage (typ): 3.3V
• Fiber Support: Yes
• Integrated Led Drivers: Yes
• Phy/transceiver Interface: MII
• Power Supply Type: Analog/Digital
• Package Type: PQFP
• Data Rate (typ): 10/100Mbps
• Vlan Support: Yes
• Operating Temperature (max): 70C
• Operating Temperature (min): 0C
• Pin Count: 128
• Mounting: Surface Mount
• Jtag Support: No
• Operating Supply Voltage (max): 3.5V
• Operating Supply Voltage (min): 3.1V
• Operating Temperature Classification: Commercial
• Interface Type: PCI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 576-1634 - BOARD EVALUATION KSZ8842-16MQL
• Current - Supply: -
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant
• Other names: 576-1478-5

Bank 0 Bus Error Status Register (0x06): BESR
This register flags the different kinds of errors on the host bus.
Bank 0 Bus Burst Length Register (0x08): BBLR
Before the burst can be sent, the burst length needs to be programmed.
Bank 1: Reserved
Except Bank Select Register (0xE).
Bank 2 Host MAC Address Register Low (0x00): MARL
This register along with the other two Host MAC address registers are loaded starting at word location 0x1 of the
EEPROM upon hardware reset. The software driver can modify the register, but it will not modify the original Host MAC
address value in the EEPROM. These six bytes of Host MAC address in external EEPROM are loaded to these three
registers as mapping below:
MARL[15:0] = EEPROM 0x1(MAC Byte 2 and 1)
MARM[15:0] = EEPROM 0x2(MAC Byte 4 and 3)
MARH[15:0] = EEPROM 0x3(MAC Byte 6 and 5)
The Host MAC address is used to define the individual destination address that the KSZ8842M responds to when
receiving frames. Network addresses are generally expressed in the form of 01:23:45:67:89:AB, where the bytes are
received from left to right, and the bits within each byte are received from right to left (LSB to MSB). For example, the
actual transmitted and received bits are on the order of 10000000 11000100 10100010 11100110 10010001 11010101.
Micrel Confidential
Bit
15
14-11
10
9-0
Bit
15
14-12
11-0
November 2005
Default Value
0
-
0
0x000
Default Value
0
0x0
0x000
R/W
RO
RO
RO
RO
R/W
RO
RW
RO
Description
IBEC Illegal Byte Enable Combination
1: illegal byte enable combination occurs. The illegal combination value can be found
from bit 14 to bit 11.
0: legal byte enable combination.
Write 1 to clear.
IBECV Illegal Byte Enable Combination Value
Bit 14: byte enable 3.
Bit 13: byte enable 2.
Bit 12: byte enable 1.
Bit 11: byte enable 0.
This value is valid only when bit 15 is set to 1.
SSAXFER Simultaneous Synchronous and Asnychronous Transfers
1: Synchronous and Asnychronous Transfers occur simultaneously.
0: normal.
Write 1 to clear.
Reserved
Description
Reserved
BRL Burst Length (for burst read and write)
000: single.
011: fixed burst read length of 4.
101: fixed burst read length of 8.
111: fixed burst read length of 16.
Reserved
55
KSZ8842-16/32 MQL/MVL
Rev. 1.4