PI7C7300DNAE Pericom Semiconductor, PI7C7300DNAE Datasheet - Page 11

• Manufacturer Part Number: PI7C7300DNAE
• Description: IC PCI-PCI BRIDGE 3PORT 272-BGA
• Manufacturer: Pericom Semiconductor

Specifications of PI7C7300DNAE

• Applications: *
• Interface: *
• Voltage - Supply: *
• Package / Case: 272-PBGA
• Mounting Type: Surface Mount
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 3 V to 3.6 V
• Supply Current (max): 660 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

1
Pericom Semiconductor
INTRODUCTION
PRODUCT DESCRIPTION
The PI7C7300D is Pericom Semiconductor’s second-generation PCI-PCI Bridge and is
an updated revision to the PI7C7300A. It is designed to be fully compliant with the 32-
bit, 66MHz implementation of the PCI Local Bus Specification, Revision 2.2. The
PI7C7300D supports only synchronous bus transactions between devices on the Primary
Bus running at 33MHz to 66MHz and the Secondary Buses operating at either 33MHz or
66MHz. The Primary and Secondary Buses can also operate in concurrent mode,
resulting in added increase in system performance. Concurrent bus operation off-loads
and isolates unnecessary traffic from the Primary Bus; thereby enabling a master and a
target device on the same Secondary PCI Bus to communicate even while the Primary
Bus is busy. In addition, the Secondary Buses have load balancing capability, allowing
faster devices to be isolated away from slower devices. Among the other features
supported by the PI7C7300D are: support for up to 15 devices on the Secondary Buses,
Compact PCI Hot Swap (PICMG 2.1, R1.0) Friendly Support and Dual Addressing
Cycle.
PRODUCT FEATURES
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
32-bit Primary and Two Secondary Ports run up to 66MHz
All 3 ports compliant with the PCI Local Bus Specification, Revision 2.2
Compliant with PCI-to-PCI Bridge Architecture Specification, Revision 1.1.
-
-
-
-
Concurrent Primary to Secondary Bus operation and independent intra-Secondary
Port channel to reduce traffic on the Primary Port
Provides internal arbitration for one set of eight secondary bus masters (S1 bus) and
one set of seven (eight if Hot Swap is disabled) secondary bus masters (S2 bus)
-
-
Supports posted write buffers in all directions
Three 128 byte FIFO’s for delay transactions
Three 128 byte FIFO’s for posted memory transactions
Enhanced address decoding
-
-
-
-
Dual Addressing cycle (64-bit)
Supports system transaction ordering rules
Tri-state control of output buffers on secondary buses
Compact PCI Hot Swap (PICMG 2.1, R1.0) Friendly Support
Industrial Temperature range –40°C to 85°C
IEEE 1149.1 JTAG interface support
3.3V core; 3.3V PCI I/O interface with 5V I/O tolerance
272-pin plastic BGA package
All I/O and memory commands
Type 1 to Type 0 configuration conversion
Type 1 to Type 1 configuration forwarding
Type 1 configuration write to special cycle conversion
Programmable 2-level priority arbiter
Disable control for use of external arbiter
32-bit I/O address range
32-bit memory-mapped I/O address range
VGA addressing and VGA palette snooping
ISA-aware mode for legacy support in the first 64KB of I/O address range
Page 11 of 107
3-PORT PCI-TO-PCI BRIDGE
November 2005 - Revision 1.01
PI7C7300D