AT32UC3A4128S Atmel Corporation, AT32UC3A4128S Datasheet - Page 12

• Manufacturer Part Number: AT32UC3A4128S
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A4128S

• Flash (kbytes): 128 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• Hardware Qtouch Acquisition: No
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 2
• Uart: 4
• Sd / Emmc: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: AES
• Sram (kbytes): 128
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

Table 3-1.
3.2.2
3.2.3
32072G–11/2011
BGA
144
K7
H4
H3
G3
E4
E3
J5
J4
QFP
144
87
42
46
79
78
76
57
56
Peripheral Functions
Oscillator Pinout
GPIO Controller Function Multiplexing
BGA
D4
100
F1
(1)
(1)
PX52
PX53
PX54
PX55
PX56
PX57
PX58
PX59
PIN
Note:
Each GPIO line can be assigned to one of several peripheral functions. The following table
describes how the various peripheral functions are selected. The last listed function has priority
in case multiple functions are enabled on the same pin.
Table 3-2.
The oscillators are not mapped to the normal GPIO functions and their muxings are controlled
by registers in the Power Mananger (PM). Please refer to the PM chapter for more information
about this.
Function
GPIO Controller Function multiplexing
Nexus OCD AUX port connections
JTAG port connections
Oscillators
103
104
105
106
107
108
109
110
G
O
P
I
1. Those balls are physically connected to 2 GPIOs. Software must managed carrefully the GPIO
2. Refer to
3. GPIO 44 is physically implemented in silicon but must be kept unused and configured in input
Supply
VDDIO
VDDIO
VDDIO
VDDIO
VDDIO
VDDIO
VDDIO
VDDIO
configuration to avoid electrical conflict.
the pad types used.
mode.
Peripheral Functions
Type
”Electrical Characteristics” on page 953
PIN
x2
x2
x2
x2
x2
x2
x2
x2
(2)
EBI - ADDR[22]
EBI - ADDR[21]
EBI - ADDR[20]
EBI - NANDWE
EBI - NCS[3]
EBI - NCS[2]
EBI - NCS[0]
EBI - NWAIT
A
DMACA - DMARQ[0]
GPIO and GPIO peripheral selection A to D
JTAG debug port
Description
OCD trace system
OSC0, OSC1, OSC32
USART3 - TXD
EIC - SCAN[3]
EIC - SCAN[2]
EIC - SCAN[1]
EIC - SCAN[0]
B
GPIO function
for a description of the electrical properties of
MCI - DATA[14]
MCI - DATA[13]
MCI - DATA[12]
USART2 - RXD
USART3 - RXD
USART2 - TXD
USART3 - TXD
MCI - CMD[1]
C
D
12