AT32UC3L0128 Atmel Corporation, AT32UC3L0128 Datasheet - Page 134

• Manufacturer Part Number: AT32UC3L0128
• Manufacturer: Atmel Corporation

Specifications of AT32UC3L0128

• Flash (kbytes): 128 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 50 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 17
• Hardware Qtouch Acquisition: Yes
• Max I/o Pins: 36
• Ext Interrupts: 36
• Usb Speed: No
• Usb Interface: No
• Spi: 5
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 460
• Analog Comparators: 8
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.62 to 3.6
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 35
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

10.5.2
Name:
Access Type:
Offset:
Reset Value:
•
•
•
•
32145A–12/2011
ARBT: Arbitration Type
FIXED_DEFMSTR: Fixed Default Master
DEFMSTR_TYPE: Default Master Type
SLOT_CYCLE: Maximum Number of Allowed Cycles for a Burst
31
23
15
–
–
–
7
0: Round-Robin Arbitration
1: Fixed Priority Arbitration
This is the number of the Default Master for this slave. Only used if DEFMSTR_TYPE is 2. Specifying the number of a master
which is not connected to the selected slave is equivalent to setting DEFMSTR_TYPE to 0.
0: No Default Master
At the end of the current slave access, if no other master request is pending, the slave is disconnected from all masters.
This results in a one cycle latency for the first access of a burst transfer or for a single access.
1: Last Default Master
At the end of the current slave access, if no other master request is pending, the slave stays connected to the last master having
accessed it.
This results in not having one cycle latency when the last master tries to access the slave again.
2: Fixed Default Master
At the end of the current slave access, if no other master request is pending, the slave connects to the fixed master the number
that has been written in the FIXED_DEFMSTR field.
This results in not having one cycle latency when the fixed master tries to access the slave again.
When the SLOT_CYCLE limit is reached for a burst, it may be broken by another master trying to access this slave.
This limit has been placed to avoid locking a very slow slave when very long bursts are used.
This limit must not be very small. Unreasonably small values break every burst and the Bus Matrix arbitrates without performing
any data transfer. 16 cycles is a reasonable value for SLOT_CYCLE.
Slave Configuration Registers
30
22
14
SCFG0...SCFG15
Read/Write
0x40 - 0x7C
0x00000010
–
–
–
6
29
21
13
–
–
5
28
20
12
–
–
4
FIXED_DEFMSTR
SLOT_CYCLE
27
19
11
–
–
3
26
18
10
–
–
2
AT32UC3L0128/256
25
17
–
9
–
1
DEFMSTR_TYPE
ARBT
24
16
8
–
0
134