ATmega32M1 Atmel Corporation, ATmega32M1 Datasheet - Page 191

• Manufacturer Part Number: ATmega32M1
• Manufacturer: Atmel Corporation

Specifications of ATmega32M1

• Flash (kbytes): 32 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 27
• Ext Interrupts: 27
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Can: 1
• Lin: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 14
• Input Capture Channels: 1
• Pwm Channels: 10
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

19.11.2
8209D–AVR–11/10
CANCDMOB – CAN MOb Control and DLC Register
• Bit 4 – BERR: Bit Error (Only in Transmission)
This flag can generate an interrupt. It must be cleared using a read-modify-write software routine
on the whole CANSTMOB register.
The bit value monitored is different from the bit value sent.
Exceptions: the monitored recessive bit sent as a dominant bit during the arbitration field and the
acknowledge slot detecting a dominant bit during the sending of an error frame.
• Bit 3 – SERR: Stuff Error
This flag can generate an interrupt. It must be cleared using a read-modify-write software routine
on the whole CANSTMOB register.
Detection of more than five consecutive bits with the same polarity. This flag can generate an
interrupt.
• Bit 2 – CERR: CRC Error
This flag can generate an interrupt. It must be cleared using a read-modify-write software routine
on the whole CANSTMOB register.
The receiver performs a CRC check on every de-stuffed received message from the start of
frame up to the data field. If this checking does not match with the de-stuffed CRC field, a CRC
error is set.
• Bit 1 – FERR: Form Error
This flag can generate an interrupt. It must be cleared using a read-modify-write software routine
on the whole CANSTMOB register.
The form error results from one or more violations of the fixed form in the following bit fields:
• Bit 0 – AERR: Acknowledgment Error
This flag can generate an interrupt. It must be cleared using a read-modify-write software routine
on the whole CANSTMOB register.
No detection of the dominant bit in the acknowledge slot.
• Bit 7:6 – CONMOB[1:0]: Configuration of Message Object
These bits set the communication to be performed (no initial value after RESET).
• CRC delimiter
• Acknowledgment delimiter
• EOF
Initial Value
Read/Write
Bit
– 00 - disable
– 01 - enable transmission
– 10 - enable reception
– 11 - enable frame buffer reception
CONMOB1
R/W
7
-
CONMOB0
R/W
6
-
RPLV
R/W
5
-
R/W
IDE
4
-
ATmega16M1/32M1/64M1
DLC3
R/W
3
-
DLC2
R/W
2
-
DLC1
R/W
1
-
DLC0
R/W
0
-
CANCDMOB
191