ATmega32M1 Atmel Corporation, ATmega32M1 Datasheet - Page 30

• Manufacturer Part Number: ATmega32M1
• Manufacturer: Atmel Corporation

Specifications of ATmega32M1

• Flash (kbytes): 32 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 27
• Ext Interrupts: 27
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Can: 1
• Lin: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 14
• Input Capture Channels: 1
• Pwm Channels: 10
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

8.5
30
Calibrated Internal RC Oscillator
ATmega16M1/32M1/64M1
Table 8-3.
Notes:
The CKSEL0 Fuse together with the SUT1..0 Fuses select the start-up times as shown in
8-4.
Table 8-4.
Notes:
By default, the Internal RC OScillator provides an approximate 8.0MHz clock. Though voltage
and temperature dependent, this clock can be very accurately calibrated by the user. The device
is shipped with the CKDIV8 Fuse programmed. See
more details.
CKSEL0
CKSEL3..1
100
0
0
0
0
1
1
1
1
101
110
111
(2)
1. The frequency ranges are preliminary values. Actual values are TBD.
2. This option should not be used with crystals, only with ceramic resonators.
1. These options should only be used when not operating close to the maximum frequency of the
2. These options are intended for use with ceramic resonators and will ensure frequency stability
device, and only if frequency stability at start-up is not important for the application. These
options are not suitable for crystals
at start-up. They can also be used with crystals when not operating close to the maximum fre-
quency of the device, and if frequency stability at start-up is not important for the application
SUT1..0
Crystal Oscillator Operating Modes
Start-up Times for the Oscillator Clock Selection
00
01
10
11
00
01
10
11
Frequency Range
Start-up Time from
Power-down and
8.0 -16.0
0.4 - 0.9
0.9 - 3.0
3.0 - 8.0
Power-save
258 CK
258 CK
1K CK
1K CK
1K CK
16K CK
16K CK
16K CK
(1)
(2)
(2)
(2)
(1)
(1)
(MHz)
Additional Delay
Recommended Range for Capacitors C1 and
14CK + 4.1ms
14CK + 4.1ms
14CK + 4.1ms
14CK + 65ms
14CK + 65ms
14CK + 65ms
(V
from Reset
“System Clock Prescaler” on page 34
CC
14CK
14CK
= 5.0V)
C2 for Use with Crystals (pF)
12 - 22
12 - 22
12 - 22
Recommended Usage
Ceramic resonator, fast
rising power
Ceramic resonator, slowly
rising power
Ceramic resonator, BOD
enabled
Ceramic resonator, fast
rising power
Ceramic resonator, slowly
rising power
Crystal Oscillator, BOD
enabled
Crystal Oscillator, fast
rising power
Crystal Oscillator, slowly
rising power
–
8209D–AVR–11/10
Table
for