ATxmega32D4 Atmel Corporation, ATxmega32D4 Datasheet - Page 117

• Manufacturer Part Number: ATxmega32D4
• Manufacturer: Atmel Corporation

Specifications of ATxmega32D4

• Flash (kbytes): 32 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 34
• Ext Interrupts: 34
• Usb Speed: No
• Usb Interface: No
• Spi: 4
• Twi (i2c): 2
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 12
• Adc Speed (ksps): 200
• Analog Comparators: 2
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 4
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 14
• Input Capture Channels: 14
• Pwm Channels: 14
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

8210B–AVR–04/10
• Bit 7:6 - Reserved
These bits are reserved and will always be read as one. For compatibility with future devices,
always write these bits to zero when this register is written.
• Bit 5:4 - EVOUT[1:0] - Event Output Port
These bits decide which port the Event Channel 0 from the Event System should be output to.
Pin 7 on the selected port is always used, and the CLKOUT bits must be set different from
EVOUT. The pin must be configured as an output pin for the Signaling Event to be available on
the pin.
Table 11-7 on page 117
Table 11-7.
• Bits 3:2 - CLKOUTSEL[1:0] - Clock Output Select
These bits are used to select which clock is output to pin.
Table 11-8.
• Bit 1:0 - CLKOUT[1:0] - Clock Output Port
These bits decide which port the Peripheral Clock should be output to. Pin 7 on the selected port
is always used. The Clock output setting, will override the Event output setting, thus if both are
enabled on the same port pin, the Peripheral Clock will be visible. The pin must be configured as
an output pin for the Clock to be available on the pin.
Table 11-9 on page 117
Table 11-9.
EVOUT[1:0]
00
01
10
11
CLKOUTSEL[1:0]
00
01
10
CLKOUT[1:0]
00
01
10
11
Event Channel 0 output configurations
Clock Output Select
Clock output configurations
shows the possible configurations.
shows the possible configurations.
Group Configuration
OFF
PC7
PD7
PE7
Group Configuration
CLK1X
CLK2X
CLK4X
Group Configuration
OFF
PC7
PD7
PE7
Description
Event out disabled
Event Channel 0 output on Port C pin 7
Event Channel 0 output on Port D pin 7
Event Channel 0 output on Port E pin 7
Description
CLK
CLK
CLK
Description
Clock out disabled
Clock output on Port C pin 7
Clock output on Port D pin 7
Clock output on Port E pin 7
PER
PER2
PER4
output to pin
output to pin
output to pin
XMEGA D
117