ATxmega32D4 Atmel Corporation, ATxmega32D4 Datasheet - Page 283

• Manufacturer Part Number: ATxmega32D4
• Manufacturer: Atmel Corporation

Specifications of ATxmega32D4

• Flash (kbytes): 32 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 34
• Ext Interrupts: 34
• Usb Speed: No
• Usb Interface: No
• Spi: 4
• Twi (i2c): 2
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 12
• Adc Speed (ksps): 200
• Analog Comparators: 2
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 4
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 14
• Input Capture Channels: 14
• Pwm Channels: 14
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

23.10.2.10
23.10.2.11
23.10.2.12
23.10.3
8210B–AVR–04/10
NVM Fuse and Lock Bit Commands
Erase User Signature Row
Write User Signature Row
Read User Signature Row / Calibration Row
The Erase User Signature Row command is used to erase the User Signature Row.
The BUSY flag in the NVM STATUS register will be set, and the CPU will be halted until the
erase operation is finished. The User Signature Row is NRWW.
The Write Signature Row command is used to write the Flash Page Buffer into the User Signa-
ture Row.
The BUSY flag in the NVM STATUS register will be set until the operation is finished, and the
CPU will be halted during the write operation. The Flash Page Buffer will be cleared during the
command execution after the write operation, but the CPU is not halted during this stage.
The Read User Signature Row and Red Calibration Row commands are used to read one byte
from the User Signature Row or Calibration Row.
The destination register will be loaded during the execution of the LPM instruction.
The NVM Flash commands that can be used for accessing the Fuses and Lock Bits are listed in
Table
For self-programming of the Fuses and Lock Bits, the Trigger for Action Triggered Commands is
to set the CMDEX bit in the NVM CTRLA register (CMDEX). The Read Triggered Commands
are triggered by executing the (E)LPM instruction (LPM). The Write Triggered Commands is trig-
gered by a executing the SPM instruction (SPM).
The Change Protected column indicate if the trigger is protected by the Configuration Change
Protection (CCP) during self-programming. The two last columns shows the address pointer
used for addressing, and the source/destination data register.
1. Load the NVM CMD register with the Erase User Signature Row command.
2. Execute the SPM instruction. This requires the timed CCP sequence during self-
1. Set up the NVM CMD register to Write User Signature Row command.
2. Execute the SPM instruction. This requires the timed CCP sequence during self-
1. Load the Z-pointer with the byte address to read.
2. Load the NVM CMD register with the Read User Signature Row / Calibration Row
3. Execute the LPM instruction.
programming.
programming.
command
23-3.
XMEGA D
283