tmp86fh09amg TOSHIBA Semiconductor CORPORATION, tmp86fh09amg Datasheet - Page 158

• Manufacturer Part Number: tmp86fh09amg
• Description: 8 Bit Microcontroller Tlcs-870/c Series
• Manufacturer: TOSHIBA Semiconductor CORPORATION

15.6
Operation Mode
Table 15-7 Flash Memory Erasing Mode
BOOT
15.6.1
ROM
Note 1: “xxH × 3” indicates that the device enters the halt condition after transmitting 3 bytes of xxh.
Note 2: Refer to "15.13 Specifying the Erasure Area".
Note 3: Refer to "15.8 Checksum (SUM)".
Note 4: Refer to "15.10 Passwords".
Note 5: Do not transmit the password string for a blank product.
Note 6: When a password error occurs, TMP86FH09AMG stops UART communication and enters the halt mode. Therefore,
Note 7: If an error occurs during transfer of a password address or a password string, TMP86FH09AMG stops UART commu-
1st byte
2nd byte
3rd byte
4th byte
5th byte
6th byte
7th byte
8th byte
9th byte
10th byte
11th byte
12th byte
13th byte
14th byte
15th byte
:
m’th byte
n’th - 2 byte
n’th - 1 byte
n’th byte
n’th + 1 byte
Table 15-7 shows the flash memory erasing mode.
Transfer Byte
Flash Memory Erasing Mode (Operating command: F0H)
when a password error occurs, initialize TMP86FH09AMG by the RESET pin and reactivate the serial PROM mode.
nication and enters the halt condition. Therefore, when a password error occurs, initialize TMP86FH09AMG by the RE-
SET pin and reactivate the serial PROM mode.
Matching data (5AH)
-
Baud rate change data (Table 15-4)
-
Operation command data (F0H)
-
Password count storage address bit
15 to 08 (Note 4, 5)
Password count storage address bit
07 to 00 (Note 4, 5)
Password comparison start address
bit 15 to 08 (Note 4, 5)
Password comparison start address
bit 07 to 00 (Note 4, 5)
Password string (Note 4, 5)
-
Erase area specification (Note 2)
-
-
(Wait for the next operation command
data)
Transfer Data from the External
Controller to TMP86FH09AMG
Page 148
9600 bps
9600 bps
9600 bps
9600 bps
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Modified baud rate
Baud Rate
- (Automatic baud rate adjustment)
OK: Echo back data (5AH)
Error: No data transmitted
-
OK: Echo back data
Error: A1H × 3, A3H × 3, 62H × 3 (Note
1)
-
OK: Echo back data (F0H)
Error: A1H × 3, A3H × 3, 63H × 3 (Note
1)
-
OK: Nothing transmitted
Error: Nothing transmitted
-
OK: Nothing transmitted
Error: Nothing transmitted
-
OK: Nothing transmitted
Error: Nothing transmitted
-
OK: Nothing transmitted
Error: Nothing transmitted
-
OK: Nothing transmitted
Error: Nothing transmitted
-
OK: Checksum (Upper byte) (Note 3)
Error: Nothing transmitted
OK: Checksum (Lower byte) (Note 3)
Error: Nothing transmitted
-
Transfer Data from TMP86FH09AMG to
the External Controller
TMP86FH09AMG