ATMEGA325-16AJ ATMEL [ATMEL Corporation], ATMEGA325-16AJ Datasheet - Page 287

• Manufacturer Part Number: ATMEGA325-16AJ
• Description: 8-bit Microcontroller with In-System Programmable Flash
• Manufacturer: ATMEL [ATMEL Corporation]

T
Note:
2570A–AVR–09/04
A
Symbol
I
V
I
t
CC
ACLK
ACID
ACIO
= -40°C to 85°C, V
1. “Max” means the highest value where the pin is guaranteed to be read as low
2. “Min” means the lowest value where the pin is guaranteed to be read as high
3. Although each I/O port can sink more than the test conditions (20 mA at V
4. Although each I/O port can source more than the test conditions (20 mA at V
at V
observed:
TQFP and MLF Package:
1] The sum of all IOL, for all ports, should not exceed 400 mA.
2] The sum of all IOL, for ports A0 - A7, C4 - C7, G2 should not exceed 100 mA.
3] The sum of all IOL, for ports B0 - B7, E0 - E7, G3 - G5 should not exceed 100 mA.
4] The sum of all IOL, for ports D0 - D7, C0 - C3, G0 - G1 should not exceed 100 mA.
5] The sum of all IOL, for ports F0 - F7, should not exceed 100 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
at V
observed:
TQFP and MLF Package:
1] The sum of all IOL, for all ports, should not exceed 400 mA.
2] The sum of all IOL, for ports A0 - A7, C4 - C7, G2 should not exceed 100 mA.
3] The sum of all IOL, for ports B0 - B7, E0 - E7, G3 - G5 should not exceed 100 mA.
4] The sum of all IOL, for ports D0 - D7, C0 - C3, G0 - G1 should not exceed 100 mA.
5] The sum of all IOL, for ports F0 - F7, should not exceed 100 mA.
Parameter
Power Supply Current
Power-down mode
Analog Comparator
Input Offset Voltage
Analog Comparator
Input Leakage Current
Analog Comparator
Propagation Delay
CC
CC
= 5V, 5 mA at V
= 5V, 5 mA at V
CC
= 1.8V to 5.5V (unless otherwise noted) (Continued)
CC
CC
= 3V for all other ports) under steady state conditions (non-transient), the following must be
= 3V for all other ports) under steady state conditions (non-transient), the following must be
(ATmega325/3250/645/6
450V)
Active 4MHz, V
(ATmega325/3250/645/6
450L)
Active 8MHz, V
(ATmega325/3250/645/6
450)
Idle 1MHz, V
WDT disabled, V
V
V
V
Condition
Active 1MHz, V
(ATmega325/3250/645/6
450V)
Idle 4MHz, V
(ATmega325/3250/645/6
450L)
Idle 8MHz, V
(ATmega325/3250/645/6
450)
WDT enabled, V
V
V
V
CC
in
CC
in
CC
CC
= V
= V
= 5V
= 5V
= 2.7V
= 4.0V
CC
CC
/2
/2
CC
CC
CC
CC
CC
CC
= 2V
= 3V
= 5V
CC
CC
= 2V
= 3V
= 5V
= 3V
= 3V
Min.
-50
ATmega325/3250/645/6450
CC
CC
= 5V, 10 mA at V
= 5V, 10 mA at V
Typ.
<10
750
500
<8
<1
CC
CC
Max.
0.55
0.25
3.5
1.5
5.5
= 3V for Port B and 10 mA
12
15
40
50
2
= 3V for Port B and 10mA
Units
mA
mA
mA
mA
mA
mA
mV
µA
µA
nA
ns
287