AM79C976 Advanced Micro Devices, AM79C976 Datasheet - Page 108
AM79C976
Manufacturer Part Number
AM79C976
Description
PCnet-PRO 10/100 Mbps PCI Ethernet Controller
Manufacturer
Advanced Micro Devices
Datasheet
1.AM79C976.pdf
(309 pages)
- Current page: 108 of 309
- Download datasheet (3Mb)
After H_RESET, the Am79C976 controller is pro-
grammed to operate in Word I/O mode. DWIO (BCR18,
bit 7) will be cleared to 0. Table 22 shows how the 32
bytes of address space are used in Word I/O mode.
All I/O resources must be accessed in word quantities
and on word addresses. The Address PROM locations
can also be read in byte quantities. The only allowed
DWord operation is a write access to the RDP, which
switches the device to DWord I/O mode. A read access
other than those listed in Table 22 will yield undefined
data, and a write operation may cause unexpected re-
programming of the Am79C976 control registers.
Table 23 shows legal I/O accesses in Word I/O mode.
Note: * The offset of a MIB counter is the value con-
tained in the MIB Offset Register plus the offset shown
in Table 7 or Table 8.
The Am79C976 controller can be configured to operate
in DWord (32-bit) I/O mode. The software can invoke
the DWIO mode by performing a DWord write access
to the I/O location at offset 10h (RDP). The data of the
write access must be such that it does not affect the in-
tended operation of the Am79C976 controller. Setting
the device into 32-bit I/O mode is usually the first oper-
ation after H_RESET or S_RESET. The RAP register
will point to CSR0 at that time. Writing a value of 0 to
CSR0 is a safe operation. DWIO (BCR18, bit 7) will be
set to 1 as an indication that the Am79C976 controller
operates in 32-bit I/O mode.
Note: Even though the I/O resource mapping changes
when the I/O mode setting changes, the RDP location
offset is the same for both modes. Once the DWIO bit
has been set to 1, only H_RESET can clear it to 0. The
DWIO mode setting is unaffected by S_RESET or set-
ting of the STOP bit. Table 24 shows how the 32 bytes
of address space are used in DWord I/O mode.
108
Table 22. I/O Map In Word I/O Mode (DWIO = 0)
00h - 0Fh
18h - 1Fh
20h-1FFh
Offset
10h
12h
14h
16h
*
No. of
Bytes
224
256
16
2
2
2
2
8
RAP (shared by RDP and BDP)
Memory-mapped Registers
Reset Register
MIB Counters
Reserved
Register
APROM
RDP
BDP
P R E L I M I N A R Y
Am79C976
All I/O resources must be accessed in DWord quanti-
ties and on DWord addresses. A read access other
than listed in Table 25 will yield undefined data, and a
write operation may cause unexpected reprogramming
of the Am79C976 control registers.
DWIO mode applies to both I/O- and memory-mapped
accesses. Either a 32-bit I/O write to offset 10h relative
to the contents of the I/O Base Address Register (BAR)
or a 32-bit memory write to offset 10h relative to the
contents of the Memory BAR puts the device into
DWIO mode. Once in DWIO mode, the offsets of the
RAP, Reset, and BDP registers are 14h, 18h, and 1Ch
relative to the contents of either the I/O BAR or the
Memory BAR.
For example, in DWIO mode the BDP Register can be
read either by an I/O read from offset 1Ch relative to the
contents of the I/O BAR or by a memory read from off-
set 1Ch relative to the contents of the Memory BAR.
DWIO mode affects only the locations between 0 and
1Fh, which include the RAP, Reset, and BDP registers.
Registers at offset 20h and above are directly ac-
cessed in memory space by byte address and are un-
affected by DWIO.
The DWIO bit is also located at bit 28 of the CMD2 reg-
ister and can be set or cleared by software regardless
of its current setting.
8/01/00
Related parts for AM79C976
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Advanced Micro Devices [4,096-Bit (512x8) Bipolar PROM]
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
Advanced Micro Devices [4,096-Bit (512x8) Bipolar PROM]
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
Advanced Micro Devices [8 Megabit (512 K x 16-Bit) CMOS 3.0 Volt-only Burst Mode Flash Memory]
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
M41000001YAdvanced Micro Devices [32 Megabit (4 M x 8-Bit/2 M x 16-Bit) CMOS 3.0 Volt-only, Simultaneous Operation Flash Memory and 4 Mbit (512 K x 8-Bit/256 K x 16-Bit) Static RAM]
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
Advanced Burst Error Processor
Manufacturer:
Advanced Micro Devices
Part Number:
Description:
Serial interface adapter (SIA)
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
Universal interrupt controller
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
256 kilobit CMOS EPROM
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
2048 x 8 static RAM, 100ns
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
Three-State Octal Buffers
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
AM2966PCOctal Dynamic Memory Drivers with Three-State Outputs
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
Three-State Octal Buffers
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
Three-State Octal Buffers
Manufacturer:
Advanced Micro Devices
Datasheet:
Part Number:
Description:
TTL programmable array logic, 7ns
Manufacturer:
Advanced Micro Devices
Datasheet: